Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Line Type Pry Bar Set (2 Piece)

The Line angled blade provides greater leverage, ground points used by Steel Erectors & Scaffolders for aligning bolt or rivet holes.

2 piece set contains:
1x 400mm.
1x 600mm.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

The Kennedy ?RASCAL BAR?

The Right Angled Seam Chisel And L Bar has been specially designed by Kennedy Tools for the separation of hard to reach spot welds and bonded panels as well as coping with the many traditional uses for pry & wrecking bars.
Features & Benefits
?Easily separates hard-to-reach spot welded or bonded panels
?Sharpened on three edges, the sharp end allows for penetration between the panels and both side edges allow for side impact to drive the panels apart without damage
?90 degrees end for use in hard-to-reach pinchweld areas
?Made from a super tough alloy steel
?Will save the technician up to 15 minutes per panel replacement
The Right Angled Rascal Bar with three sharpened edges is designed to allow two-directional hammer use on quarter panels, rockers and any other pinchweld. The sharp end allows for penetration between the panels and the two lower edges allows for side impact to drive the panels apart. The chisel tip can be used for starting seam separation.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from square section Chrome Vanadium steel with ground points. Impact resistant plastic handles offer a more comfortable and secure grip to make these pry bars the most user friendly available. Handles are oil and acid resistant. Suitable for a wide range of general duty applications within the packing, automotive, maintenance and assembly industries. Ideally suited to most tradesmen.

Curved Blade

For general duty prising and levering. The curved blade will provide greater leverage.
Set contents:
3 piece: 1 of each 300mm Straight, 300mm & 450mm Curved
2 piece: 1 of each 450mm & 600mm Curved

Protector Sleeves

Contoured high impact resistant plastic grips redirects the force of mishits safely away from your hands preventing injury. Suitable for use with octagonal cold chisels.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Brick Bolster

Suitably hardened for the purpose of splitting and cutting brickwork or stone smoothly and cleanly. Do not use as a lever.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from square section Chrome Vanadium steel with ground points. Impact resistant plastic handles offer a more comfortable and secure grip to make these pry bars the most user friendly available. Handles are oil and acid resistant. Suitable for a wide range of general duty applications within the packing, automotive, maintenance and assembly industries. Ideally suited to most tradesmen.

Straight Blade

For general duty prising and levering. The curved blade will provide greater leverage.
Set contents:
3 piece: 1 of each 300mm Straight, 300mm & 450mm Curved
2 piece: 1 of each 450mm & 600mm Curved