Table Top Slat Chain

A complete range of table top chains and sprockets in steel, stainless steel and molded thermoplastics. These are manufactured specifically for a conveying applications.
Some table top chains have been standardised between manufacturers. We show below the most popular ranges but with many specialty attachments and options available on table top chain, please contact your local service centre to assist in identifying and recommending the right table top chain for your application.

981T Series TAB - Side Flexing Chain

Reduced Flight Gap
Material: Superior grade of cold
rolled special ferritic
stainless steel
Length: 10?

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 17/B (SPB/17)

Spherical Roller Bearings - C3 Tolerance

Premier range - material improvements give:
• Increased capacity.
• Extended service life.
• Reduced friction torque.
• Will tolerate temperatures up to 200°C.
• Steel and brass cages.
• Available from UK stock.

Taper Bore

SNR Deep Groove Ball Bearings

Rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects.

Sealed Deep Groove Ball Bearings

Dimensions to IS015

Conti Synchrobelt Timing Belts

? Moderately oil-resistant
? Temperature range -20C up to +100C
(depending on application)
? Non-aging and ozone-resistant
? Suitable for tropical climates
Size designation (example)
150XL037
150 150? (381.0mm) pitch length
XL 0.2? (5.08mm) tooth pitch
037 3/8? (9.25mm) timing belt width

DIN 5296

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Adapter Sleeves

Adaptor sleeves are commonly used for locating tapererd bored bearing and securing them to a shaft. They can be accurately positioned and dismounted. By using in conjuction with SNR feeler gauges accurate radial clearances will be achieved.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.