Optibelt Timing Belts

Optibelt?s Omega timing belts give long lasting
high performance with a number of advantages:
Reduced noise.
Runs in both standard HTD and RPP pulleys.
High efficiency - up to 98%.
Maintenance-free.

Omega High Quality Timing Belts

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

Continental Contitech V-Belts

Heavy duty cogged raw edge V-belts, DIN 7753. Moderately oil-resistant. Resistant to temperature from -30 to 80°C.

Electrically conductive (anti-static) to ISO 1813. Insensitive to dust.
Suitable for tropical climates.
Belt Section 13/A (XPA/13)

Conti-V-Advance V-Belts

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Take-Up Units - ST Type

Cast iron self lube units are used where shaft adjustments are required on applications such as conveyor systems.

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

Max Width (b1) 13mm, Height (h)8mm.

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.
Belt Section 13/A (SPA/13)

Conti-V Ultraflex V-Belts

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 17/B (SPB/17)

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

Cast Iron Motors - 2P

Cast Iron Frame Motors - IE2 (Eff1 Premium Efficiency). Suitable for inverter duty applications. Regreasing nipple from frame 225S/M and above. Thermistors (1 per phase) fitted in
frame 160M and above.

Cast Iron - B5 - Flange Mounted - 2 Pole - 3,000rpm - AC 3 Phase

SNR Bearings

SNR has developed a complete range of high quality ball thrust bearings. Thrust bearings are designed to maintain the shaft in one single direction. They admit low rotating speeds and sustain high axial loads.

You are strongly advised against submitting them to radial loading. Ball thrust bearings are comprised of separate items facilitating installation and maintenance. Grease and oil lubrication is feasible.

Applications: vertical shaft, lathe tailstock, plate-type pumps.

51200 Series Ball Thrust Bearings