Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 10/Z (SPZ/10)

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Flanged Housing Unit - MSF Type Square - Four Bolt

Made of grey cast iron with four fixing holes.

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Plummer Blocks - Medium Series - NP Type

Cast iron self lube unit plummer blocks. Medium series.
With two slotted holes for fixing.

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 22/C (SPC/22)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

Adapter Sleeves

Adaptor sleeves are commonly used for locating tapererd bored bearing and securing them to a shaft. They can be accurately positioned and dismounted. By using in conjuction with SNR feeler gauges accurate radial clearances will be achieved.

Adapter Sleeves

Adaptor sleeves are commonly used for locating tapererd bored bearing and securing them to a shaft. They can be accurately positioned and dismounted. By using in conjuction with SNR feeler gauges accurate radial clearances will be achieved.

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)