SNR Deep Groove Ball Bearings

Open type without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

Open Deep Groove Ball Bearings

Dimensions to ISO15

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 10/Z (SPZ/10)

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

Max Width (b1) 13mm, Height (h)8mm.

Table Top Slat Chain

A complete range of table top chains and sprockets in steel, stainless steel and molded thermoplastics. These are manufactured specifically for a conveying applications.
Some table top chains have been standardised between manufacturers. We show below the most popular ranges but with many specialty attachments and options available on table top chain, please contact your local service centre to assist in identifying and recommending the right table top chain for your application.

820 Series - Straight Running

Material: Ultra performance acetal resin
Length: 10?.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Rubber sealed type:

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Inch Sizes

Keyways to BS 46 Part 1.

Weg Frequency Inventers

The WEG CFW series of Variable Speed Drive (VSD) is intended for speed control of three-phase induction motors.
Applications: Centifugal Pumps, Process Pumps, Fans/Exhausters, Stirrers/Mixers, Extruding Machines, Conveyors, Roller Tables, Granulators, Pelletising Machines, Driers,
Rotating Ovens, Rotating Filters, Winders, Unwinding Machines, Cutting and Welding Machines.

CFW-10

In addition to a very small, easily mounted package, simplified keypad and bright LED readout, complete diagnostics and fully programmable I/Os, the CFW-10 controls 3PH AC motors with a single phase 120V AC input voltage and will produce three phase 230V to drive motors up to 0.75kW and single phase 230V AC. Will also produce three phase 230V to drive motors up to 2.2kW. There is no requirement for a set-up transformer to operate three phase 230VAC motors when only single phase 115V is available. The CFW-10 is an economical solution
to many
applications.

Dimensions
(H x W x D):
132 x 95 x 121mm.

Weight: 0.9kg.

SNR Shaft Seals & Adaptors

Cover plates are made of corrosion-resistant steel and used where the shaft terminates inside the housing. In this configuration only one seal set will be required.

Cover Plates