VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 17/B (SPB/17)

Double-row Self-Aligning Ball Bearings - Sealed Type

The spherical race in the outer ring allows angular displacement. It has good ability to withstand radial loads. Its design, however, means that it can only accept very low axial loads. These bearings are pre-greased but seals limit angular travel possibilities to 1/20. Basic loads are the same as the series 12 and 13 bearings of the same diameter, as they have the same internal design definition. The misalignment angle must nevertheless be limited in order to remain within values compatible with the sealing system used, the permissible misalignment is limited to 0.5

Spherical Roller Bearings

Spherical roller bearings are double row units comprising solid outer rings with a concave raceway, solid inner rings and barrel rollers with cages. We stock both the plain (symmetrical) bore (EAW33) and taper bore (EAKW33).
The symmetrical barrel rollers orientate themselves freely on the concave outer raceway. As a result, shaft flexing and misalignment of the bearing seats are compensated.

Plain Bore

Simplex Chain

1/2" Pitch simplex carbon steel chain suitable to a wide range of applications supplied in 10 feet lengths.

Pitch: 12.70mm
Ult. Strength: 18.60kN

126SRX10FT European Series

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 22/C (SPC/22)

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 13/A (SPA/13)

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.