Spherical Roller Bearings - C3 Tolerance

Premier range - material improvements give:
• Increased capacity.
• Extended service life.
• Reduced friction torque.
• Will tolerate temperatures up to 200°C.
• Steel and brass cages.
• Available from UK stock.

Plain Bore

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 13/A (SPA/13)

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Open Type

Without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

SNR Pillow Block Housings

The housings are produced from grey cast iron in compliance with DIN EN 1561 and external surface painted RAL 5010 - Gentian Blue) the machined surfaces are treated with an anti-corrosion agent. Threaded for grease nipple or automatic lubrication and grease drain hole which is sealed with a metal threaded plug at the factory but can be removed subject to application.
Housings based on ISO 113/II: 1994 and DIN 736: 1984 to DIN 739: 1984.

500 Series for use with tapered bore from 1200K, 2200K, 22200K and 23200K with shaft diameter: 20mm to 140mm. 600 Series for use with tapered bore from 1300K, 3200K, 21300K and 22300K with shaft diameter: 20mm to 90mm.

Wide Series Deep Groove Ball Bearings - C3 Clearance

Slightly wider than the 6200 series with the same bore and outside diameter. Designed to withstand radial loads, withstand axial loads in both directions and operate at high speeds of rotation.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Optibelt Timing Belts

Optibelt?s Omega timing belts give long lasting
high performance with a number of advantages:
Reduced noise.
Runs in both standard HTD and RPP pulleys.
High efficiency - up to 98%.
Maintenance-free.

Omega High Quality Timing Belts

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Spherical Roller Bearings

Spherical roller bearings are double row units comprising solid outer rings with a concave raceway, solid inner rings and barrel rollers with cages. We stock both the plain (symmetrical) bore (EAW33) and taper bore (EAKW33).
The symmetrical barrel rollers orientate themselves freely on the concave outer raceway. As a result, shaft flexing and misalignment of the bearing seats are compensated.

Taper Bore

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...A, 33...A

Contact angle 25, no filling slots and can accept axial loads in both directions. These bearings have synthetic material cages.