Optibelt Timing Belts

Optibelt?s Alpha timing belts are manufactured from high grade polyurethane with steel reinforcing cords.

High precision profile for good repeatability.
Very low stretch.
Resistant to many oils and chemicals.
Wide and flexible range.

Alpha Polyurethane Timing Belts

T-Pitch Range - T2.5, T5, T10

Gilkes Submersible Pumps

Submersible pumps for drainage, de-watering and general transfer of both clean and dirty liquids. AISI304 stainless steel housing and impeller. 230V 50Hz single phase.
Motors are 0.25 to 2.25kW and are all IP68.
Max. liquid temperature 40°C.
Max immersion
depth 5m.
Solid size: 7 - 20mm.
Power cable length minimum 5m.
Available with or without the float switch.
Applications:
• Emptying of sump pits, rainwater tanks.
• Irrigation
• Emergency removal of flood waters in basements
• Transfer duties for clear, sandy and muddy liquids
• Residential and industrial waste water pumping
• Sewage treatment and disposal
• Industrial effluent plants


Image for illustration
purposes only.

Titan 2XL Submersible Pump in Stainless Steel

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

SNR Bearings

SNR has developed a complete range of high quality ball thrust bearings. Thrust bearings are designed to maintain the shaft in one single direction. They admit low rotating speeds and sustain high axial loads.

You are strongly advised against submitting them to radial loading. Ball thrust bearings are comprised of separate items facilitating installation and maintenance. Grease and oil lubrication is feasible.

Applications: vertical shaft, lathe tailstock, plate-type pumps.

51100 Series Ball Thrust Bearings

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

Deep Groove Ball Bearings

Widely used in machinery, automobiles, tractors, machine tools, motors, pumps, agricultural machinery and other high speed facilities.

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 22/C (SPC/22)

Lock Nuts

Used primarily to help lock and locate bearings on shafts or adaptor sleeves. They have evenly spaced slots on the circumference for use with the SNR range of hook spanners.