产品 / 轴承 & 滚轴
编号：OPB6884061R
●产品描述：
SK High Power Wedge Belts
To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.
Belt Section 13/A (SPA/13)
编号：OPB6882635N
●产品描述：
SK High Power Wedge Belts
SK wedge belts offer significant performance advantages with up to 97% drive efficiency with extended belt life and easier fitting.
S=C Plus length tolerance* Belts are automatically length matched to very tight tolerances and so require no matching, are easier to fit and run more efficiently in sets.
Example: SPC 5000 tolerance range = +/-2mm compared to DIN standard/other manufacturers = +/-50mm
Advanced manufacturing techniques like our rotational curing process mean that our SK belts are less prone to fatigue and absorb less power in wrapping around the pulley, resulting in improved drive efficiency and longer belt life.
*applies to belts over 1160mm length. Consult catalogue for details.
Dimensions: 487 to 12500mm.
Standard range further sizes on request.
Belt Section 10/Z (SPZ/10)
编号：OPC6882145G
●产品描述：
Optibelt Timing Belts
Optibelt?s Omega timing belts give long lasting
high performance with a number of advantages:
Reduced noise.
Runs in both standard HTD and RPP pulleys.
High efficiency - up to 98%.
Maintenance-free.
Omega High Quality Timing Belts
编号：OPB6881065V
●产品描述：
VB Classical V-Belt
V-Belts to BS3790, DIN2215 and ISO 4184.
Belt Section 10/Z (SPZ/10)
编号：OPB6951331J
●产品描述：
Taper Bore Bushes
Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.
Metric Sizes
Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.
编号：OPB6951224B
●产品描述：
Taper Bore Bushes
Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.
Metric Sizes
Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.
编号：OPB6951532K
●产品描述：
Taper Bore Bushes
Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.
Metric Sizes
Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.
编号：OPB6888214W
●产品描述：
Super X-Power V-Belt
Moulded Cogged Raw Edge Wedge Belts
Belt Section 10/Z (SPZ/10)
编号：OPB6951451F
●产品描述：
Taper Bore Bushes
Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.
Metric Sizes
Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.
编号：OPB6881458N
●产品描述：
Optibelt Timing Belts
Open ended or joined polyurethane timing belts.
Can be supplied in 50m rolls or cut to any length*.
Can be joined to make a belt of any length*.
Ideal for conveying applications.
Available with a range of backings and attachments.
*Note - length must be a multiple of the tooth pitch.
Other pitches and widths available include:
T20, AT20, 5M, 8M, L, H, ATL10.
Price is /metre based on a 50m roll. Please add 10% for cut lengths. Price for joined to length belts and belts with special backings and attachments on application.
Alpha Linear Polyurethane Timing Belts