SMC Pneumatic Fittings

Air Cylinders
CD85 Series
Double acting.

CD85 Series Air Cylinders

Manifold Block Assemblies

Manifold block assemblies for manifold expansion. One-touch timing.
*Blanking plate assemblies.

Gates Hydraulic Couplings

Male JIC, Parallel. 37° Cone.

Bosch Rexroth Pneumatic Fittings

AS2-FRE Series Filter pressure regulator
G - G 3/8
Filter porosity: 5 m
Lockable
With pressure gauge
ATEX Certified.

For further specification on this product please see the attached PDF under the additional information tab.

AS2-FRE Series Air Line Regulator

Low Pressure 2 Way Ball Valve

Female x female valves which combines good design with superior materials and engineering to provide long operating life with low maintenance costs.
Materials:
Body: brass, surface nickel plated.
Ball: brass, nickel and mirror finish chrome plated.
Spindle: brass.
Seat/seals: PTFE.
O-Ring: Viton.
Handle: steel lever c/w thermo insulating sleeve.
Threads: manufactured to ISO-7 unless otherwise stated.

Port Size Pressure Rating (Bar)
? 64
3/8? 64
? 64
? 40
1? 40
1? 25
1? 25

KHN88 Series

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2040 Series

Hand Operated Crimper

Lightweight, portable, hand-operated crimper is compact and ideal for mobile use. It allows the manufacture of factory quality hose assemblies on site in a few seconds.

Hose Capacity: 1/4" - 1"
Calibration: Accurate to 1/10th of s mm
Crimping power: 27 Tonnes (265kN)
Dimensions: 460mm x 280mm x 390mm
Weight: 24kg

SMC One-Touch Fitting Female Connectors

KQF
To pipe from the male threaded portion of a pressure gauge, etc.
KQF04-01: Tube O.D. 4mm. Thread: RC1/8.
KQF06-01: Tube O.D. 6mm. Thread: RC1/8.

Mounting Accessories

Trunnion Pins

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Tank Connectors

For use on water tanks and cisterns.