Bosch Rexroth Pneumatic Fittings

For further specification on this product please see the attached PDF under the additional information tab.

Series CN1 Electrical Connector

Series DO accessories.
Electrical connectors, series CN1
ISO 6952 Electrical connectors, form B.
Ambient temperature min./max -25C / 40C
Protection class according to EN 60529: IP65
Cable fitting: M16x1,5
Mounting screw tightening torque: 0.4Nm


For further specification on this product please see the attached PDF under the additional information tab.

Kennedy® Strainer for AVD110 and AVD220

To suit AVD110 & AVD220

SMC One-Touch Plug-In Reducer

KQ2R
One-touch plug-in reducer.
For connecting to smaller one-touch fittings.

KQ2R04-06 Tube O.D. 4mm x fit dia 6mm.
KQ2R04-08 Tube O.D. 4mm x fit dia 8mm.
KQ2R04-10 Tube O.D. 4mm x fit dia 10mm.
KQ2R06-04 Tube O.D. 6mm x fit dia 4mm.
KQ2R06-08 Tube O.D. 6mm x fit dia 8mm.
KQ2R06-10 Tube O.D. 6mm x fit dia 10mm.
KQ2R06-12 Tube O.D. 6mm x fit dia 12mm.
KQ2R08-10 Tube O.D. 8mm x fit dia 10mm.
KQ2R08-12 Tube O.D. 8mm x fit dia 12mm.
KQ2R10-12 Tube O.D. 10mm x fit dia 12mm.



Colour: white.

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female BSP, O-Ring Swivel. 60° Cone - 90° Swept Elbow

Camozzi Swivel Run Tees

S6440
Super-rapid fittings for plastic tubes. Push-in fitting swivel run Tee.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
12mm tube - G3/8 thread.

Kennedy® Horizontal Rear Hinges

Available in cylinder diameters of 32mm, 40mm, 50mm, 63mm, 80mm and 100mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Female Parallel

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2080 Series

Mounting Accessories

Single Rear Clevis

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Elbows

Connects pipes at 90