Manifold Block Assemblies

Manifold block assemblies for manifold expansion. One-touch timing.
*Blanking plate assemblies.

Manually Operated Valves

Series: 3
Function: 5/2
Port: 1/8
Actuation: - Knob - Bistable

Manually Operated Valve - Knob

Body Ported Manifolds

Suitable valves for these manifolds: SY**20 types.

Series 32 Compact Magnetic Cylinders

Double Acting.
Standard ISO 21287.
Stainless steel rod.
Anodized aluminium extrusion.
Cast aluminium End Blocks.
Double Acting Stroke min-max Ø 20-25 : 510-500mm, Ø 20 : 10-500mm, Ø 25 : 10-500mm.
Bores: Ø 16, 20, 25.
Operating temperature: 0°C to +80°C (with dry air -20°C to +80°C).
Operating Pressure:
1 to 10 bar (Double-acting).
2 to 10 bar (Single-acting).
Speed: 10 to 1000mm/sec (no load).

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Male BSP Parallel, 60 Cone

Type MBSPP.

Bosch Rexroth Pneumatic Fittings

For further specification on this product please see the attached PDF under the additional information tab.

OCT/PRE Series Cylinder Mounting Plate

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Elbows

Connects pipes at 90

Camozzi Equal Tees

7540
Super-rapid compact fitting Technopolymer equal tube Tee.
Available in 4, 6, 8, and 10mm tubes.

In-Line Type

AS series in line speed controllers minimise installation time and cost as they reduce the mounting height and enable compact machinery design. The number of needle rotations has been increased from 8 to 10 turns to permit easy control at low speeds. Applicable tube material nylon, soft nylon and polyurethane tubing.
Operating pressure: 1MPa max.

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

One Touch Male Connectors