Thin/2 Jaw Mechanical Pullers

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
086000 Spread: 75mm. Reach: 75mm.
086100 Spread: 150mm. Reach: 150mm.
086200 Spread: 150mm. Reach: 225mm.
086300 Spread: 150mm. Reach: 225mm.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

"Multipull" Blind Housing Puller

For the removal of blind housing bearings without the need to dismantle machinery or remove the running shaft. Positive seating allows even tension on the inner and outer bearing rings reducing resistance. The stabilisers reduce sideways movement and self centres the puller. The three sets cover a range of ISO bearings, if there is no ISO reference on the bearing refer to the puller spread and adaptor.



098000 - ISO designation: 6004-6010, 6004-6015. Reach: 125mm. Adaptor diameter: 5.5 - 8mm.098100\t - ISO designation: \t6299-6205, \t6200-6211 & 6212-6222. Reach: 415mm. Adaptor diameter: 5.5 - 12.5mm.098200\t - ISO designation: \t6300-6302 Reach: 490mm. Adaptor diameter: 16 - 31.75mm.

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily & efficiently. The spring loaded plunger provides direct, non- twisting application of thrust safely.

2 and 3 Jaw Kit

Combination twin/triple leg puller kits. Complete with ram extension. 155000: Spread: 150mm. Reach: 150mm. Extension: 50mm. Contains components to make up 4 different pullers. In metal box.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Separator & Puller Combination Set

Manufactured from forged alloy steel. Taper jaws allow the separator to be used where access behind the component is too restricted to use normal pullers.



Set contains components to make five different puller/separator combinations: 10mm, 89mm reach three jaw internal or external puller. Thin jaw, two jaw puller internal or external. 55mm diameter separator.

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily and efficiently. The spring loaded plunger provides direct, non-twisting application of thrust safely.

Hydraulic Micro Puller - 3 Jaw

The jaws are manufactured from drop-forged steel with independent leaf springs for positive location. Suitable for the rapid removal of small bearings. Spread: 19 - 45mm.Reach: 73mm.