Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

ER Collet Chucks

E4 to DIN 6499/B

XP-90C ?4 Square? Milling Cutters

The Indexa-Seiki XP-90C ?4 square? milling cutters are a positive 90 cutter with an exact angle of 90, square inserts allow deep passes and high feed rates per teeth. Torx style insert pocket with shim seats help protect the body in the event of an accident. The unique Plasma Ion coating offers longer tool life and greater hardness and increases wear resistance. Through tool coolant as standard, for optimum machining results.

For all technical specifications please refer to our catalogue

Indexa-Seiki Indexable Tooling Spares

Within the Index-Seiki? range of indexable tooling spares you will find insert screws, Torx? keys, shims, clamps and pins to fit the Index-Seiki? toolholder you?re using.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Radial

Short B1 Right Hand

Indexa-Seiki Standard Pull Studs

BT-MAS 403

Indexa-Seiki Tru-Loc Milling Chucks

The mechanical advantage provided by the 'roller lock' mechanism produces a high clamping force, along the full length of cutter shank. The force is applied evenly and so enables the chuck to hold cutters within 0.010mm at 100mm from chuck nose concentricity, giving improved component surface finish, holding better workpiece tolerances, reducing vibration and prolonging tool life. Manufactured from special alloy steel, heat treated to close hardness tolerances. Internal seals protect against entry of swarf and dirt. Tru-Loc milling collets with back stop adjustment screws ensure quick and easy cutter pre-setting and replacement, eliminating tool creep. A range of milling chucks for finishing and semi-finishing applications, with accurate tolerances and high quality surface finish.

Using the Tru-Loc Milling Chuck - when tightening the chuck use the recommended wrench and tighten fully - but without means of extra leverage. N.B. The gap between the locking ring and body may vary between 0 & 3mm dependent on cutter shank size and collet used. Maintenance: To get the best performance from this Tru-Loc milling chuck please ensure it is serviced on a regular basis by a qualified agent. It is recommended that this is at least once every twelve months. Failure to do this may affect the performance of the chuck and/or invalidate any guarantee. Collet reference PSC/PSCa.

Tru-Loc Milling Chuck IS40 Shank

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 3.0-26.
(D)41mm x (L)46mm.

ER40

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 2.0-20.
(D)33mm x (L)40mm.

ER32

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 1.0 - 7.0.
(D)11.5mm x (L)18.0mm.

ER11

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

ER Collet Chucks

E4 to DIN 6499/B