Indexa-Seiki Indexable Tooling Spares

Within the Index-Seiki? range of indexable tooling spares you will find insert screws, Torx? keys, shims, clamps and pins to fit the Index-Seiki? toolholder you?re using.

Indexa-Seiki KC3 - Adaptors

Combination shank. Allows Kennedy & Clarkson throw-away milling cutters to be used with standard 16mm Weldon and screwed chucks/collets.

KC3 Combi Shank Adaptor

Indexa-Seiki Universal Locking Tool Fixtures

Made from Cast Iron with machined carbon steel fittings, these fixtures are an invaluable asset in your machine shop. Universal in use, suitable for use with BT, DIN and CAT - 50 tool holders. Designed to give maximum protection for your tool holder whilst enabling strong gripping power to be exerted in both horizontal and vertical positions. It is tough but remains light in weight and its compact design makes it ideal for mounting on a work table or tool cart.

BT/DIN/CAT 50 Universal Tool Tightening Fixture

Indexa-Seiki? ER Collets

Indexa-Seiki? ER collets are the most versatile toolholding system for any operation that utilises a round shank cutting tool in a machining centre. Typical applications include drilling, milling, tapping, reaming and boring.

When Indexa-Seiki? ER collets are used with round shank cutting tools the collet chucks centralise the cutting tool and if all the ER system components have been maintained correctly, this should result in increased tool life, higher feed rates, better work piece accuracy and enhanced work piece finish.

ER Collet Set

Indexa-Seiki? ER Collets are available in the in a range of sizes to maximise efficiency in most applications, they are manufactured from hardened and tempered high alloy steel. All supplied in hardwearing bench cases with protective foam inserts.

Conform to DIN 6499.
Up to 10.0mm - 0.015mm TIR.
11.0 to 18.0mm ? 0.015 to 0.020mm TIR.
19.0 to 26.0mm ? 0.015 to 0.020mm TIR.

For all technical and dimensional specifications please refer to our catalogue.

Indexa-Seiki Standard Pull Studs

BT-MAS 403

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 2.0-20.
(D)33mm x (L)40mm.

ER32

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2-1 Boring Bar Sleeves

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Radial

Short, Upside down B4 Left Hand

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

ER Collet Chucks

E4 to DIN 6499/B

Indexa-Seiki Standard Pull Studs

BT-MAS 403