WNMG Indexable Turning Inserts

QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.

AC3000 Carbide Grade (P20 - P40, M20 - M40)

Al2O3 Coated Grade
Designed for interrupted cuts of steels and stainless.

NUP Chipbreaker

Application: optimised machining.

VCGT

K10 (ISO K10) Uncoated. Used in combination with a high rake geometry for machining Aluminiums, Plastics and other soft Non-Ferrous materials.



Suitable for External Toolholders

TNMG Indexable Turning Inserts

T9025 (ISO P20-P30, M20-M30) MT-CVD Coated. Increased wear resistance provided by the new "Double-Bridge" coating technology allowing for higher cutting conditions. Universal grade for medium to rough turning of steel at medium speed.TM-Medium operation chipbreaker.

CNMG Indexable Turning Inserts

T6030 (ISO M20-M40) CVD Coated. Having a high heat resistance and good adhesion between coating layer and substrate, favourable chemical and mechanical properties allows for maximum process reliability and efficiency. Used for continuous and interrupted cutting of extremely difficult to cut Mo-enriched Stainless Steel, Austenites, Austenite-Ferrite, Duplex and Cast Stainless Steel with a high Mo content.

Mitsubishi Indexable Milling Inserts

Mitsubishi APX4000 Milling inserts have been developed using advanced simulation technology to produce a new 15mm insert is suitable for larger depths of cut. The new insert is also thicker and therefore ideal for high load machining they are also:
Efficient when machining on low rigidity machines or work pieces and they are ideal for thin wall or extended reach applications.
They have efficient heat disposal and chip control, heat generated during cutting has been reduced due to the APX?s special geometry.
Ideal chip shape formed by the insert for easy disposal.

AOMT Indexable Milling Insert

Mitsubishi grade description: VP15TF (P15-P35/M15-M35/K15-K30) PVD ''Miracle'' Coated Milling/Drilling Grade. Offers increased heat resistance and adhesion strength. For all Steels, Cast Irons and some Stainless Steel

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR?s standard blocks.

TAG N-C Parting & Grooving Inserts

First choice for the parting of bars, hard materials and tough applications. A positive rake, single cavity with negative land and shoulders, provides extra cutting-edge strength, medium-to-high feeds.

IC808 Grade description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

CNMG

Suitable for External/Internal Toolholders

TCMT

QX5020 (ISO P10-P35 M10-M30 K10-K30) CVD Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.

CCGX

Suitable for External/Internal Toolholders