Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® Power Tool Chisels

Suitable for tools with SDS Max system.

Kennedy® Router Cutters

With ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Suitable for straight or curved work.

Two Flute Flush Trimming Bits

Freud Circular Saw Blades

Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)

Blue Line - Fine

Cross cut blades, designed with a high TPI. Suitable for cross grain cutting solid wood giving a good finish.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Rotabroach Mini Cutters

For perfect holes in sheet metal, pipes & plastic. Cut clean, burr-free holes in seconds with new Roatabroach Mini-Cutters, the professional solution to holemaking in sheet metal, pipes and plastics. Mini-Cutters produce holes by removing a 'disc' of metal and have precision ground teeth and flutes to rapidly remove waste material, so they are fast, smooth and highly accurate. Now they come with a new and more aggressive tooth geometry to give high higher performance and longer cutting life on stainless steel and other difficult materials. No toolbox is complete without Mini-Cutters for clean, precise and effortless holecutting every time. Over 3 times faster than twist drills Mini-Cutters have multiple teeth and an annular
cutting action with no 'dead centre' area as with a twist drill. It means that less pressure is required to make the hole, so there is less risk of deforming sheet metal. This highly efficient cutting action also ensures minimal burring on breakthrough, reducing or completely eliminating the need for additional finishing work. Last up to 300 times longer than hole saws Holesaws have stamped teeth which only remove
small particles of metal with each revolution whereas Mini-Cutters are precision ground cutting instruments which slice their way through sheet metal without leaving burrs or jagged edges. Because they are made from M2 High Speed Steel,
they retain their sharpness to give a longer, more reliable cutting life over thousands of holes.

Senator® 12 Piece Router Cutter Set

Manufactured from high speed steel with tungsten carbide tips. Suitable for use with all portable routing machines. Ideal for craft work, light duty and workshop use.



Contents:
Two Flute Core Box Bit: 12.7mm diameter x 6.3mm radius.
Two Flute Core Bit: 22mm diameter x 6.3mm radius with ball bearing guide.
Two Flute Dovetail Bit: 12.7mm diameter x 14° side cutting angle.
Two Flute Chamfering Bit: 32mm diameter x 45° side cutting angle with ball bearing guide.
Two Flute Flush Trimming Bit: 12.7mm diameter with ball bearing guide.
Two Flute Straight Trimming Bit: 16mm diameter x 12.4mm cutting length.
Two Flute Rounding Over Bit: 22mm diameter 6.3mm radius with ball bearing guide.
Two Flute Straight Trimming Bit: 12mm diameter x 20mm cutting length.
Two Flute Straight Trimming Bit: 6mm diameter x 19mm cutting length.
Two Flute Rounding Over Bit: 28.6mm diameter x 9.5mm radius with ball bearing guide.
Two Flute Dovetail Bit: 12.7mm diameter x 90° inclusive cutting angle.
Two Flute Roman Ogee Bit: 25mm diameter x 14.5mm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Router Cutters

With ball bearing guide. For edge mould on coving, picture frames, etc. Self guiding with ball bearing.

Two Flute Cove Bits