产品 / 动力工具 & 磨料磨具 / 电动工具附件
编号：TRE2872212V
●产品描述：
Trend Router Cutters
General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.
Two Flute Straight Plunging Bits
1/4" and 1/2" Shanks
编号：FRE2803013N
●产品描述：
Freud Circular Saw Blades
Anti-kickback Design: Kickback is caused by over-feed. It happens so quickly it can be impossible to react before injury occurs. On a table saw the wood is thrown back violently, on a radial arm saw the blade climbs quickly out of the cut and on a hand held saw the saw is pushed out of the cut. Freud's design reduces this. Each tooth is followed by a limiter, which restricts bite to the maximum safe amount. Teflon Coating. Resistant to friction and heat build-up. Teflon coated blades last longer, cleaning is easy and the distinctive coating also gives rust resistance.Whisper Quiet Expansion Slots: A question-mark shaped slot allows for the necessary expansion yet reduces noise. Laser Cut, High Strength Bodies: The use of precision lasers to avoid unwanted stress in the metal. The method also allows the use of higher strength steel (40 to 45 Rc). These bodies remain true, even after years of use. Tensioned Blades for Superior Flatness: Pre-tensioned blades ensure years of smooth operation. The process is computer controlled and was designed and built by Freud. Advanced Tri-Metal Tip Brazing: Copper alloy is sandwiched between layers of silver alloy (Copper is soft and will stretch without residual stresses, insulating the shoulders from impacts.)
Red Line - Medium
General purpose blades, with medium TPI. For cutting both long grain and cross grain solid wood, giving a good finish.
编号：KEN2803905K
●产品描述：
Kennedy® "Ultimate" Merino Sheepskin Bonnets
Genuine 100% sheepskin tie-on bonnets ideal for polishing metal, glass fibre, wood and painted surfaces. With tie cord. 32mm pile. Maximum 2,500rpm - Best results are obtained with a tool speed of 1,500 - 2,000rpm. Not suitable for wet use. Support pad supplied separately.
编号：TRE2872117P
●产品描述：
Trend Router Cutters
General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.
Two Flute Straight Plunging Bits
1/4" and 1/2" Shanks
编号：KEN2873140K
●产品描述：
Kennedy® Router Cutters
Cutter for deep mortising and grooving. Staggered cutting edges give good chip clearance enhancing quality of cut.
Two Flute Staggered Tooth Bits
编号：KEN2802530K
●产品描述：
Kennedy® Pin Spanners for Angle Grinders
Several types available. Weight 110g.
Pin Spanner
To suit Kennedy® 100mm pads and most 100mm electric grinders.
Pitch: 20.
Pin diameter: 3.4.
编号：SEN2877170K
●产品描述：
Senator® Router Cutters
For profiling, rebating and through slotting.
Straight Trimming Bits
1/4" Shank.
编号：KEN2882140K
●产品描述：
Kennedy® M2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Long Series
Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.
编号：KEN2876680K
●产品描述：
Kennedy® Router Cutters
For mounting slotting cutters. Optional ball bearing guide which also ensures a constant depth of slot.
Slotting/Jointing Cutter Arbors
编号：KEN2882320K
●产品描述：
Kennedy® M2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Long Series
Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.