Rexroth T-Unions

QR1-RTT Series
2x push-in fitting T-union with external thread.
Available in threads:
G1/8 x 6mm diameter.
G1/8 x 8mm diameter.
G1/4 x 6mm diameter.
G1/4 x 8mm diameter.
G1/4 x 10mm diameter.
G1/4 x 12mm diameter.
G3/8 x 10mm diameter.
G3/8 x 12mm diameter.
G3/8 x 14mm diameter.
G1/2 x 12mm diameter.

Ambient temperature min/max: +0°C/+60°C.
Working pressure min/max: -0.95 bar/10bar
Materials:
Housing: Polybutyleneterephthalate.
Seal: Acrylonitrile Butadiene Rubber.
Tooth lock washer: Stainless steel.
Release ring: Polyoxymethylene.
Release ring holder: Die cast zinc; Brass, nickel-plated.
Thread: Brass, nickel-plated.

Series S6510

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Male Stud Coupling

SMC One-Touch Mini Male Adaptor

KJH
Use to pipe in the same direction from female thread. Most general style.
KJH04-M3: Tube O.D. 4mm. Thread T: M3 x 0.5.
KJH04-M5: Tube O.D. 4mm. Thread T: M5 x 0.8.
KJH06-01S: Tube O.D. 6mm. Thread T: R1/8.
KJH06-M5: Tube O.D. 6mm. Thread T: M5 x 0.8.

Rexroth Connection Pieces

QR1-RDS Series
Pin bushing connection pieces.
Available in 4, 6, 8 and 10mm diameters.

Ambient temperature min/max: +0°C/+60°C.
Working pressure min/max: -0.95 bar/10 bar.
Materials:
Housing: Polybutyleneterephthalate.

Series 2043

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Female Y Connector

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Brass Wingback Elbow

This fitting is made of the following components:-

The body is produced in brass
'O'Rings are nitrile rubber
The collet is produced in acetal copolymer with stainless steel teeth

Camozzi Female Run Tees

2050
Series 2000 pipe fittings BSPT adaptor male/female run Tee.
Available in threads:
G1/8 overall length 37mm.
G1/4 overall length 46mm.
G3/8 overall length 48.5mm.
G1/2 overall length 60.5mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Series 6000 Series Pneumatic Fitting Kits

These kits are available for a range of tube diameters and contain the most commonly used Series 6000 Super Rapid brass push in fittings.
Each kit contents:
3x 6540 Series equal tube tee
3x 6580 Series tube to tube
connector
3x 6550 Series equal tube elbow
5x S6520 Series swivel elbow
10x S6510 Series male stud

Camozzi Male Run Tees - Taper

2070
Series 2000 pipe fittings BSPT adaptor male/female run Tee.
Available in threads:
G1/8 overall length 37mm.
G1/4 overall length 46mm.
G3/8 overall length 48.5mm.
G1/2 overall length 60.5mm.