Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Straight Tap Connectors

With brass swivel nut and sealing washer. Suitable for central heating systems.

Camozzi Swivel Run Tees

S6440
Super-rapid fittings for plastic tubes. Push-in fitting swivel run Tee.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
12mm tube - G3/8 thread.

PCL "100 Series" Airline Couplings (Hi-Duty)

Large diameter allows greater airflow making them suitable for industrial applications - free air flow rate at 7bar/100PSI: 100 to 120cfm (2830 to 3400ltr/min). All steel construction with hardened shoulder protects against accidental disconnection. Hard wearing passivated zinc finish.

Male Threaded

SMC One-Touch Union Elbow Connectors

KQ2L
One-touch union elbow.

KQ2L04-00: Tube dia: 4mm.
KQ2L06-00: Tube dia: 6mm.
KQ2L08-00: Tube dia: 8mm.
KQ2L10-00: Tube dia: 10mm.
KQ2L12-00: Tube dia: 12mm.
KQ2L16-00: Tube dia: 16mm.



Colour: white.

SMC One-Touch Plug-In Reducer

KQ2R
One-touch plug-in reducer.
For connecting to smaller one-touch fittings.

KQ2R04-06 Tube O.D. 4mm x fit dia 6mm.
KQ2R04-08 Tube O.D. 4mm x fit dia 8mm.
KQ2R04-10 Tube O.D. 4mm x fit dia 10mm.
KQ2R06-04 Tube O.D. 6mm x fit dia 4mm.
KQ2R06-08 Tube O.D. 6mm x fit dia 8mm.
KQ2R06-10 Tube O.D. 6mm x fit dia 10mm.
KQ2R06-12 Tube O.D. 6mm x fit dia 12mm.
KQ2R08-10 Tube O.D. 8mm x fit dia 10mm.
KQ2R08-12 Tube O.D. 8mm x fit dia 12mm.
KQ2R10-12 Tube O.D. 10mm x fit dia 12mm.



Colour: white.

Series 2530

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Male - Female Reducers

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

One Touch Male Connectors

Kobe? Airline Coupling Adaptors

Case hardened with passivated finish. For use with 'Standard' and 'Vertex' type couplings. Hard wearing passivated zinc finish for double protection against corrosion.

Female Threaded

1/4" BSPT.

PCL "60 Series" Airline Couplings

Designed for general industrial applications - free flow air rate at 7 bar/100PSI: 55 to 60 CFM (1557 to 1698 ltr/min). All steel construction with hard wearing passivate finish. Hardened steel shoulder to prevent accidental disconnection in use. Designed and manufactured in Sheffield by PCL this traditional PCL coupling range offers above average airflow characteristics for general and portable air tool applications in garage and tyre shop environments.
Hardened steel shoulder prevents accidental disconnection
Secure locking device
Swivel feature prevents kinking of the hose
Specially designed valves and large aperture provides optimum air flow.

Female Threaded

3/8" BSPT.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Tube suitability: Nylon, polyurethane.

Non-Return Valve Female to Female

Pressure Range: 2 to 8 bar. Temperature Range: -25°C to +90°C.