Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

?Superseal? Pipe Inserts

The Superseal Pipe Insert has been developed to be used with Speedfit Barrier Pipe and Speedfit fittings to provide an extra line of defence when installing a Speedfit Push Fit System. The insert has its own ?O?Ring which, together with a Stem sliding within the pipe ID, gives a secondary seal against the inside of the fitting. The Speedfit connection, when made with the Insert, has a number of design features. Sliding the stem of the insert into the pipe gives greater compression of the main ?O?Ring on the pipe and greater rigidity of the length of pipe within the fitting, reducing the chance of leaks if a side load is applied. A connection is easier to make because the head of the insert has been designed for ease of insertion.

SMC One-Touch Union Y-Connectors

KQU
To branch tubing in the same direction. Colour: black.
KQU04-00: Tube: O.D. 4mm.
KQU06-00: Tube: O.D. 6mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Tee

SMC One-Touch Union Elbow Connectors

KQ2L
One-touch union elbow.

KQ2L04-00: Tube dia: 4mm.
KQ2L06-00: Tube dia: 6mm.
KQ2L08-00: Tube dia: 8mm.
KQ2L10-00: Tube dia: 10mm.
KQ2L12-00: Tube dia: 12mm.
KQ2L16-00: Tube dia: 16mm.



Colour: white.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Flexi Hoses - Union Nut

Flexi Hoses are manufactured to the high quality you would expect from Speedfit. The hoses are suitable for hot and cold water services, have a working pressure of 10 Bar and have WRAS and NHBC Approval.

Camozzi Multiple Tees

7545
Super-rapid compact fitting Technopolymer multi Tee.
Available in:
2x6mm - 3x4mm tube.
2x8mm - 3x6mm tube.
2x10mm - 3x8mm tube.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Elbow Connector

PCL Tailpieces & Threaded Connectors

A comprehensive range designed for use in conjunction with airline couplings in garage and industrial applications. Case hardened with zinc finish.

Male Threaded Tailpieces

For connecting a hose to a female threaded fitting.

PCL® Safeflow Safety Coupling

Safe and simple to use. Enhances workshop safety - prevents hose whip. Creates a safe compressed air environment. Two stage self-venting release. Genuine PCL product, designed and manufactured in Sheffield, England. Hard wearing steel construction with corrosive resistant finish.
Conforms to ISO 4414:1998 and EN 983:1996. Genuine PCL product, designed and manufactured in Sheffield, England.
Compatible with standard adaptors.

Integral Tailpiece