Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Barrier Pipes

Manufactured to BS7291 parts 1 and 3 Class S and CS kite marked.

Copper Compression Fittings

Manufactured to EN 1254 (formerly BS864/2), and carrying the prestigious Kitemark, Prestex ?type A? compression fittings are suitable for mechanically joining copper or stainless steel tube by means of compressing a cone into a tube without the application of heat. The range is designed for use with copper tube to BS EN 1057: 1996 (formerly BS2871: part1 ), BS2871: part 2, or stainless steel tube to BS4127: 1994). Fittings are available in brass, all with brass cap nuts as standard.

Elbow Connectors

Copper x Copper. Connects plain pipe at 90.

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RPN Series Straight Pneumatic Fitting

Standard metric M5-G 1/2 straight push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2080 Series

PCL XF Series Airline Couplings (EURO 130)

A heavy duty design to meet the demands of all manufacturing and end user applications. Offering superior flow characteristics - free air flow at 7 bar/100PSI : 135CFM (3820 Ltr/min). Quick release action with corrosion resistant plating compatible with European adaptor styles CEJN320, RECTUS 25 and 26 Series.

Female Threaded

1/2" BSPT.

Camozzi Female/Female Couplers

2543
Series 2000 pipe fittings BSP adaptor female adapter.
Available in G1/8, G1/4, G3/8 and G1/2 threads.

Camozzi Distribution Blocks

Series 2000 pipe fittings BSP adaptor 4-way anodised aluminium distribution block.
Available in threads:
G1/8 overall length 25mm.
G1/4 overall length 32mm.
G3/8 overall length 40mm.
G1/2 overall length 50mm.

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Plug

Compressed air fitting.
This fitting is made of the following components:-

The entire body is produced in acetal copolymer

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Female Parallel

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Tees

Connects plain pipe end to end and at 90.