Series 1000 Rapid Fittings for Plastic Tubes

They can be used with rigid PA tubes. A locking nut is provided and can be tightened both manually and with a spanner. The special shape of the guiding cone ensures that the tube cannot be accidentally cut.
General data:
Materials body and nut: nickel-plated brass; O-ring: NBR; thread seals: PTFE, PA, AL
Threads GAS, conical ISO 7 (BSPT) GAS, cylindrical ISO 228 (BSP)

Series 1541 Swivel Elbow Sprint

SMC One-Touch Plug-In Elbow Connectors

KQ2L
Plug-in elbow. Colour: white.
KQ2L04-99: Tube O.D. 4mm x fit dia 4mm.
KQ2L06-99: Tube O.D. 6mm x fit dia 6mm.
KQ2L08-99: Tube O.D. 8mm x fit dia 8mm.
KQ2L10-99: Tube O.D. 10mm x fit dia 10mm.
KQ2L12-99: Tube O.D. 12mm x fit dia 12mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Male Taper

SMC One-Touch Female Elbow Connections

KQ2
KQ2LF04-01: Tube O.D. 4mm. Thread: RC1/8.
KQ2LF04-01: Tube O.D. 4mm. Thread: RC1/4.
KQ2LF06-01: Tube O.D. 6mm. Thread: RC1/8.
KQ2LF06-02: Tube O.D. 6mm. Thread: RC1/4.
KQ2LF06-03: Tube O.D. 6mm. Thread: RC3/8.
KQ2LF08-01: Tube O.D. 8mm. Thread: RC1/8.
KQ2LF08-02: Tube O.D. 8mm. Thread: RC1/4.
KQ2LF08-03: Tube O.D. 8mm. Thread: RC3/8.



Colour: white.

Copper Compression Fittings

Manufactured to EN 1254 (formerly BS864/2), and carrying the prestigious Kitemark, Prestex ?type A? compression fittings are suitable for mechanically joining copper or stainless steel tube by means of compressing a cone into a tube without the application of heat. The range is designed for use with copper tube to BS EN 1057: 1996 (formerly BS2871: part1 ), BS2871: part 2, or stainless steel tube to BS4127: 1994). Fittings are available in brass, all with brass cap nuts as standard.

Straight Compression Fittings

Straight connectors for use on plain joints.

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Brass Stem Adaptor

Converts push fit end to male thread.
The body is manufactured from solid brass

Rexroth Bulkhead Plug Connector

QR1-RSC Series
Push-in fitting plastic bulkhead plug connector.
Available in diameters: 6, 8, 10 and 12mm.

Ambient temperature min/max: +0°C/+60°C.
Working pressure min/max: -0.95 bar/10 bar.
Materials:
Housing: Polybutyleneterephthalate.
Seal: Acrylonitrile Butadiene Rubber.
Tooth lock washer: Stainless steel.
Release ring: Polyoxymethylene.
Release ring holder: Die cast zinc; Brass nickel-plated.

Series S6440

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Swivel Run Tees

PCL Airline Coupling Adaptors

Case hardened with passivated finish. For use with 'Standard' and 'Vertex' type couplings. Hard wearing passivated zinc finish for double protection against corrosion.

Male Threaded

3/8" BSPT.

Camozzi Bulkhead Couplings

6590
Super-rapid fittings for plastic tubes. Push-in fitting bulkhead coupling.
Available in 4mm, 6mm, 8mm, 10mm and 12mm tubes.