Camozzi Male Stud Couplings

S6510
Super-rapid fittings for plastic tubes. Push-in fitting-male stud.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
10mm tube - G1/2 thread.
12mm tube - G1/4 thread.
12mm tube - G3/8 thread.
12mm tube - G1/2 thread.

SMC One-Touch Mini Different Diameter Union Y-Connectors

KJU
Use to branch line with size down in the same direction.
KJU04-00: Tube O.D. 2x 4mm x 6mm.

In-Line Type

AS series in line speed controllers minimise installation time and cost as they reduce the mounting height and enable compact machinery design. The number of needle rotations has been increased from 8 to 10 turns to permit easy control at low speeds. Applicable tube material nylon, soft nylon and polyurethane tubing.
Operating pressure: 1MPa max.

Rexroth Push-In Connectors

QR1-RAS Series
Push-in plastic fittings with external thread for compressed air hoses.
Available in threads:
G1/8 x 6mm diameter.
G1/8 x 8mm diameter.
G1/4 x 6mm diameter.
G1/4 x 8mm diameter.

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RVL Series Long Elbow Pneumatic Fitting

Standard metric M5-G 1/2 Long Elbow push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

SMC One-Touch Mini Equal Y-Connectors

KJU
Use to branch line in the same direction.
KJU04-00: Tube O.D. 4mm.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

White Pipe Clip

Not to be fitted any closer than 60mm from end of fitting.

SMC One-Touch Fitting Bulkhead Connectors/Bulkhead Union

KQ2E
One-touch fitting bulkhead connector/bulkhead union.

KQ2E04-00: Tube dia: 4mm. Port size: 4mm.
KQ2E06-00: Tube dia: 6mm. Port size: 6mm.
KQ2E08-00: Tube dia: 8mm. Port size: 8mm.
KQ2E10-00: Tube dia: 10mm. Port size: 10mm.
KQ2E12-00: Tube dia: 12mm. Port size: 12mm.
KQ2E16-00: Tube dia: 16mm. Port size: 16mm.

Camozzi Multi Swivel Tee

7542
Super-rapid compact fitting Technopolymer multi Tee with O-ring assembled.
Available in:
6mm, 3x4mm tube, G1/8 thread.
6mm, 3x4mm tube, G1/4 thread.
8mm, 3x6mm tube, G1/8 thread.
8mm, 3x6mm tube, G1/4 thread.
10mm, 3x8mm tube, G1/4 thread.
10mm, 3x8mm tube, G3/8 thread.

Series 6000 Series Pneumatic Fitting Kits

These kits are available for a range of tube diameters and contain the most commonly used Series 6000 Super Rapid brass push in fittings.
Each kit contents:
3x 6540 Series equal tube tee
3x 6580 Series tube to tube
connector
3x 6550 Series equal tube elbow
5x S6520 Series swivel elbow
10x S6510 Series male stud