Nail Puller

Used for pulling nails which are either protruding or buried. Hammer action \tsleeve drives jaws into wood around nail. The pivoting jaw ensures a tighter grip the harder the pull.

Burgess Engravers

Suitable for intricate engraving or security/identification marking. Each engraver is balanced to sit comfortably in the hand. The one hundred strokes per second penetrating pump action ensures the engraving point indents the workpiece rather than removing raw material from the workpiece, which could weaken it or change the molecular structure. The fine electro magnetic penetration adjustment allows use on a wide range of soft and hard materials including steel, plastic, glass and ceramics. Machined brass jaws prevent damage to engraving points if excess pressure is applied.

Professional Engraver Kit - Model 741

With heavy duty, continuous rated motor. Motor rating: continuous. Points supplied: A2, A4, A5 & A8.

Burgess Engravers

Suitable for intricate engraving or security/identification marking. Each engraver is balanced to sit comfortably in the hand. The one hundred strokes per second penetrating pump action ensures the engraving point indents the workpiece rather than removing raw material from the workpiece, which could weaken it or change the molecular structure. The fine electro magnetic penetration adjustment allows use on a wide range of soft and hard materials including steel, plastic, glass and ceramics. Machined brass jaws prevent damage to engraving points if excess pressure is applied.

Engraving Points for Burgess Engravers

A2: for glass and steel. Solid carbide.
A4: for hardened steel. Carbide tipped.
A5: for soft metals and alloys.
A6/A7: ball points for metal embossing, hammering and leather work.
A8: abrasive point for frosting glass and smoothing.
A80: diamond point for fine glass engraving.

Burgess Engravers

Suitable for intricate engraving or security/identification marking. Each engraver is balanced to sit comfortably in the hand. The one hundred strokes per second penetrating pump action ensures the engraving point indents the workpiece rather than removing raw material from the workpiece, which could weaken it or change the molecular structure. The fine electro magnetic penetration adjustment allows use on a wide range of soft and hard materials including steel, plastic, glass and ceramics. Machined brass jaws prevent damage to engraving points if excess pressure is applied.

Engraving Points for Burgess Engravers

A2: for glass and steel. Solid carbide.
A4: for hardened steel. Carbide tipped.
A5: for soft metals and alloys.
A6/A7: ball points for metal embossing, hammering and leather work.
A8: abrasive point for frosting glass and smoothing.
A80: diamond point for fine glass engraving.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from square section Chrome Vanadium steel with ground points. Impact resistant plastic handles offer a more comfortable and secure grip to make these pry bars the most user friendly available. Handles are oil and acid resistant. Suitable for a wide range of general duty applications within the packing, automotive, maintenance and assembly industries. Ideally suited to most tradesmen.

Curved Blade

For general duty prising and levering. The curved blade will provide greater leverage.
Set contents:
3 piece: 1 of each 300mm Straight, 300mm & 450mm Curved
2 piece: 1 of each 450mm & 600mm Curved

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Pitching/Masons Chisel

A stone dressing chisel for removing excess stone and facing work. Bevelled on one side.