SiteSafe® Contractor Flat Cold Chisels c/w Hand Guard

Manufactured from high quality octagonal chrome vanadium steel with a ground cutting edge, in accordance with BS 3066. For use on brickwork, masonry and cold metals.

Stanley 12” Wonderbar® Pry Bar

1-55-555
Forged, high carbon steel for increased strength and durability. Heat-treated for increased durability. Polished and bevelled cutting edges. Contoured bar makes pulling nails, prying, lifting and scraping easier. Bevelled nail slot at both ends. High visibility,
powder-coated finish.
Blade width: 44mm (1.3/4”).
Overall length: 314mm (12.3/8”).

SiteSafe® Contractor Cold Chisels

SiteSafe® Contractor cold chisels are available as flat chisels, cross cut chisels, brick bolsters and electricians' floor chisels. They are all manufactured from high strength octagonal section chrome vanadium steel with ground cutting edges.

Conform to BS3066.

Contractor Brick Bolster Chisels

SiteSafe® Contractor brick bolster chisels used for splitting bricks. Supplied with a fitted contoured high impact resistant plastic grip, that redirects the force of mis-strikes safely away from your hand. SiteSafe® chisel guards help prevent injury.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Line Type Pry Bar Set (2 Piece)

The Line angled blade provides greater leverage, ground points used by Steel Erectors & Scaffolders for aligning bolt or rivet holes.

2 piece set contains:
1x 400mm.
1x 600mm.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel and V-Notch Wrecking Bars

Multifunctional tools used mainly for prising and levering, drawing large nails and demolition work, ideal for any general dismantling and stripping applications. The versatile Super lever type can be used as a light duty nail lifter, pry bar, adze or lever

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Flat Chisel

Used by the engineering and building trades for cutting and chipping cold metals, brick work and stone. The angle of the cut edge should be 60 - 70, inclusive, but is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from square section Chrome Vanadium steel with ground points. Impact resistant plastic handles offer a more comfortable and secure grip to make these pry bars the most user friendly available. Handles are oil and acid resistant. Suitable for a wide range of general duty applications within the packing, automotive, maintenance and assembly industries. Ideally suited to most tradesmen.

Straight Blade

For general duty prising and levering. The curved blade will provide greater leverage.
Set contents:
3 piece: 1 of each 300mm Straight, 300mm & 450mm Curved
2 piece: 1 of each 450mm & 600mm Curved

SiteSafe® Contractor Flat Cold Chisels

Manufactured from high quality octagonal chrome vanadium steel with a ground cutting edge, in accordance with BS 3066. For use on brickwork, masonry and cold metals.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Rolling Head Pry Bar Set (3 Piece)

The rolling head design is ideally suited for use in confined spaces, ground points used by steel erectors and scaffolders for aligning bolt or rivet holes.

3 piece set contains:
1x 150mm.
1x 300mm.
1x 450mm.