Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Chisel and V-Notch Wrecking Bars

Multifunctional tools used mainly for prising and levering, drawing large nails and demolition work, ideal for any general dismantling and stripping applications. The versatile Super lever type can be used as a light duty nail lifter, pry bar, adze or lever

SiteSafe® Contractor Flat Cold Chisels c/w Hand Guard

Manufactured from high quality octagonal chrome vanadium steel with a ground cutting edge, in accordance with BS 3066. For use on brickwork, masonry and cold metals.

Kennedy Crowbars, Wrecking bars and Pry bars

Manufactured from carbon steel. These traditional designs are used by tradesmen in all industrial environments. Suitable for a wide range of general duty applications, ideal for dismantling timber constructions, opening packing cases and removing nails (depending on the type of bar). Also used in assembly applications offering safe leverage and alignment capability.

Rolling Head Pry Bar Set (3 Piece)

The Rolling Head design is idealy suited for use in confined spaces, ground points used by Steel Erectors & Scaffolders for aligning bolt or rivet holes.
3 piece set contains; 1 of each 150mm, 300mm & 450mm.

Stanley Fatmax™ Hand Tools

The Stanley Fatmax wrecking bar is forged, from high-carbon steel able to withstand 975 ft-lbs. of bending momentum.

Tri-lobe design increases strength, durability and ease of use.

High-visibility, powder-coated finish.

Slotted claw and bevelled ends improve functionality and performance.

Available in three lengths:
356mm (14") Order Code: STN-585-5540K
610mm (24") Order Code: STN-585-5540P
915mm (36") Order Code: STN-585-5540W

Fatmax? Wrecking Bar

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Electricians Bolster/Flooring chisel

Generally used by Electricians and Plumbers for cutting the tongue, in tongue and groove floorboarding, requiring a flexible blade to give sufficient leverage to raise a floorboard enough to insert a lever bar prior to laying pipes or wiring.

Yamoto? Cold Chisels and Punch Sets

This Yamoto? cold chisel and punch set contents everything you'll need to mark metal, realign holes, driving pins in/out of machine assemblies to cutting metal brickwork or stone.

Yamoto? tools are manufactured to meet and satisfy the needs of the industrial user.

CPS014 Cold Chisel and Punch Set (14 Pieces)

The CPS014 14 piece cold chisel and punch set from Yamoto? is manufactured from drop forged chrome vanadium steel and have ground cutting edges* the set contents the following types of chisels and punches:

Pin punches ideal for driving tight fitting pins out of mechanical assemblies or realigning holes to fit dowel pins. Manufactured from hardened and tempered steel. With a hexagonal body for extra grip.

Centre punches manufactured from hardened and tempered steel with a hexagonal body for positive grip. Precision ground 60 point for accurate marking of work pieces.

Cold chisels are used by the Engineering and building trades to remove waste metal when a very smooth finish is not required, cutting and chipping brickwork or stone and when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The angle of the cutting edge should be 60 to 70 degrees, inclusive, but it is dependant on the material to be cut. When cutting metal, the softer the material is, the more acute the cutting angle should be.

Taper punches used for aligning holes in jigs and fixtures etc. With a hexagonal body for extra grip.

*Where applicable.

Contents:
Pin punches: 3/16''x6'', 3/32''x4 1/4'', 1/8''x4 3/4'', 3/16''x5 1/4'' & 1/4''x5 3/4''.
Centre punches: 5/32''x5''.
Cold Chisels: 1/2''x6'', 5/8''x6 1/2'', 3/4''x7 1/2'' and 7/8'' x8''.
Taper punches: 3/16''x10'', 7/32''x10'', 5/16''x10'' and 3/8''x10''.

Protector Sleeves

Contoured high impact resistant plastic grips redirects the force of mishits safely away from your hands preventing injury. Suitable for use with octagonal cold chisels.

Electric Pencil

Used to etch metal for easy identification. Six settings allow use on softer metals without damaging the workpiece. Needles are made from a special heat resisting tungsten alloy to retain sharpness and avoid welding to the workpiece. Settings: Alter the position of the contact plugs on the transformer to change the depth of the etching.

SiteSafe® Contractor Flat Cold Chisels

Manufactured from high quality octagonal chrome vanadium steel with a ground cutting edge, in accordance with BS 3066. For use on brickwork, masonry and cold metals.

Kennedy Cold Chisels

Kennedy cold chisels are manufactured from high quality, high strength octagonal section chrome vanadium steel with ground cutting edges. They are are used to channel brickwork, concrete, chip stone and to remove waste metal when a very smooth finish is not required or when the work cannot be done easily with other tools, such as a hacksaw, file, bench shears or power tools. The head of each chisel is chamfered to slow down the formation of the mushroom shape caused by hammering. Conform to: BS3066.

Half Round/ Bullnose Chisels

Used for cutting round bottomed grooves in steel such as oil grooves and also for 'roughing up' surfaces to be chipped by a flat chisel. The job is made easier by cutting grooves across the surface with this type of chisel then the raised portion can be easily chipped away with a flat blade.
Cutting angle 40 - 50 degrees to the vertical.