RexPro Carbon Steel Chain

With RexPro, Rexnord set a new standard for quality chains. The RexPro chain is the result of further developing the
Rexnord high performance chain. Over a timespan of four years the combination of selected steels, optimised manufacturing and the RexPro lubrication have all achieved these outstanding product characteristics.

American Standard Connecting Links - Triplex Connecting Link

Double-row Self-Aligning Ball Bearings - Sealed Type

The spherical race in the outer ring allows angular displacement. It has good ability to withstand radial loads. Its design, however, means that it can only accept very low axial loads. These bearings are pre-greased but seals limit angular travel possibilities to 1/20. Basic loads are the same as the series 12 and 13 bearings of the same diameter, as they have the same internal design definition. The misalignment angle must nevertheless be limited in order to remain within values compatible with the sealing system used, the permissible misalignment is limited to 0.5

Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 10/Z (SPZ/10)

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Inch Sizes

Keyways to BS 46 Part 1.

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Flanged Housing Unit - MFC Type Round - Four Bolt

Made of grey cast iron with four fixing holes.

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

Donghua Roller Chain

The Donghua Chain Group is one of the world's largest chain manufacturers with an established global network; producing over 30 million metres of finished chain each year. Donghua's primary focus is quality and its advanced manufacturing techniques, combined with complete control of the production process from the selection of raw material through to the assembly of each component ensure Donghua Chain provides high performance solutions across all applications.

Duplex Roller Chain American Standard

Duplex Chain

SNR Deep Groove Ball Bearings

Rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects.

Sealed Deep Groove Ball Bearings

Dimensions to IS015

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Outer Ring and Inner Ring is without Ribs

Lock Nuts

Used primarily to help lock and locate bearings on shafts or adaptor sleeves. They have evenly spaced slots on the circumference for use with the SNR range of hook spanners.