Conti-V Ultraflex

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.

Belt Section 22/C (SPC/22)

Weg Frequency Inverters

The WEG CFW series of Variable Speed Drive (VSD) is intended for speed control of three-phase induction motors.
Applications: Centifugal Pumps, Process Pumps, Fans/Exhausters, Stirrers/Mixers, Extruding Machines, Conveyors, Roller Tables, Granulators, Pelletising Machines, Driers,
Rotating Ovens, Rotating Filters, Winders, Unwinding Machines, Cutting and Welding Machines.

CFW-08

Easy to install and operate. Equipped with optimised software that can be easily set through a keypad, which enables them to process and control most of industrial machines.

Dimensions (H x W x D): 151 x 75 x 131mm.

Weight: 1.0kg.

SNR Deep Groove Ball Bearings

Open type without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

Open Deep Groove Ball Bearings

Dimensions to ISO15

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

Optibelt Timing Belts

Optibelt?s Alpha timing belts are manufactured from high grade polyurethane with steel reinforcing cords.

High precision profile for good repeatability.
Very low stretch.
Resistant to many oils and chemicals.
Wide and flexible range.

Alpha Polyurethane Timing Belts

AT-Pitch Range - AT5, AT10

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Continental Contitech V-Belts

Heavy duty cogged raw edge V-belts, DIN 7753. Moderately oil-resistant. Resistant to temperature from -30 to 80°C.

Electrically conductive (anti-static) to ISO 1813. Insensitive to dust.
Suitable for tropical climates.
Belt Section 13/A (XPA/13)

Conti-V-Advance V-Belts

Tab Washers

Tab washers are used for securing KM series lock nuts. They have an inner tab for location on the adaptor sleeve. One of the external tabs is bent over a slot when used wit the
KM series lock nuts.

SNR Shaft Seals & Adaptors

The SNR SC...SV series consists of a contact washer made of corrosion-protected steel with a vulcanised rubber lip to locate in the housing.

The V-Ring seal has axial contact after being fitted to the shaft with the face of the washer. If the shaft extends through the housing one seal pack must be
ordered for both side of the housing.

Other sealing arrangements are available through your local service branch.

Pillow Block V-Ring Seals