Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Flanged Housing Unit - MSF Type Square - Four Bolt

Made of grey cast iron with four fixing holes.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Plummer Blocks - Medium Series - NP Type

Cast iron self lube unit plummer blocks. Medium series.
With two slotted holes for fixing.

Self-Aligning Ball Bearings

2200 & 2300 Series self-aligning ball bearings are double row with a concave raceway to allow approximately 4° of misalignment. They have a tapered bore for use with adaptor sleeves. There are also a range of sealed versions available.

Cylinder Bore

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Open Type

Without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

SNR Pillow Block Housings

The housings are produced from grey cast iron in compliance with DIN EN 1561 and external surface painted RAL 5010 - Gentian Blue) the machined surfaces are treated with an anti-corrosion agent. Threaded for grease nipple or automatic lubrication and grease drain hole which is sealed with a metal threaded plug at the factory but can be removed subject to application.
Housings based on ISO 113/II: 1994 and DIN 736: 1984 to DIN 739: 1984.

500 Series for use with tapered bore from 1200K, 2200K, 22200K and 23200K with shaft diameter: 20mm to 140mm. 600 Series for use with tapered bore from 1300K, 3200K, 21300K and 22300K with shaft diameter: 20mm to 90mm.

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.