SNR Bearings

SNR has developed a complete range of high quality ball thrust bearings. Thrust bearings are designed to maintain the shaft in one single direction. They admit low rotating speeds and sustain high axial loads.

You are strongly advised against submitting them to radial loading. Ball thrust bearings are comprised of separate items facilitating installation and maintenance. Grease and oil lubrication is feasible.

Applications: vertical shaft, lathe tailstock, plate-type pumps.

51100 Series Ball Thrust Bearings

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...B, 33...B

Contact angle 32, with filling slots and accept axial loads (higher loads than Type A) in a predominant direction. Cage in pressed steel, synthetic material or machined brass.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Narrow Series Deep Groove Ball Bearings - C3 Clearance

Slightly narrower than the 6000 series with the same bore and outside diameter. Designed to withstand radial loads, withstand axial loads in both directions and operate at high speeds of rotation.

Housed Bearing Units

Housed Bearing Units are one of the most effective and easiest solution to accomodate misalignment. Units below consist of housing and insert. A wide range is available including Imperial sizes. Please ask for further information.

Flanged Housing Unit - MSF Type Square - Four Bolt

Made of grey cast iron with four fixing holes.

SNR Deep Groove Ball Bearings

Rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects.

Sealed Deep Groove Ball Bearings

Dimensions to IS015

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.