Flange Sealant Gasket Dressing

Suitable for parts which require disassembly, Resistant to petrochemicals, lubricants, water, weak acids & alkalis.

5922

5331 - Threadsealer Sealant

Recommended for use on threaded plastic or plastic/metal fittings carrying hot or cold water e.g. industrial and agricultural plastic water pipe systems, or drainage systems.
WRC approved to 85C (Potable Water)
P1 NSF Reg. No:123620

518 - Flexible Fast Cure Gasket

Recommended for sealing aluminium flanges and fills up to 0.5mm. Withstands fluctuations in pressure, temperature and vibration. Replaces pre-cut gaskets on rigid parts.

Loctite 598, High performance silicone sealant

Loctite 598, High performance silicone sealant for use as flexible gaskets Excellent oil resistance high flexibility temperature range: 200C continuous operation short-term exposure up to 260C.

Activators for Thread & Gasket Sealants

7649N - Recommended for use when a very fast cure is required. 7471T - Recommended for use at below 15C or on inactive surfaces.

Loctite Gasket

Loctite 5188 has been designed to function in the most demanding applications with superior adhesion and flexibility, even after heat ageing. Loctite 5188 takes anaerobic gasketing to a new level. Typical applications include metal to metal assemblies of machined flanges such as gearboxes, housings, covers, etc.

5188 Highly Flexible Anerobic Gasket 50ml

5400 Medium Strength Thread Sealant

LOCTITE® 5400™ is designed for the locking and sealing of
metal threaded pipes and fittings. The product cures when
confined in the absence of air between close fitting metal
surfaces and prevents loosening and leakage from shock and
vibration. The thixotropic nature reduces the migration of liquid product after application to the substrate.



Technical Data:
• Maximum thread size: M80, R3"
• Strength: Medium
• Viscosity: 5,000 - 20,000 mPa∙s
• Breakaway torque: 19Nm
• Service temperature range: -55°C - +150°C
• Pack size: 50ml

Benefits:
• Leading in health and safety.
• No hazard symbols, no risk phrases & no safety phrases.
• “White” Material Safety Data Sheet – no entries in
sections
2, 3, 15 and 16 of MSDS acc. to (EC) No. 1907/2006 – ISO
11014-1.
• Excellent chemical and thermal resistance of cured product.
• Thixotropic nature: less migration of liquid product after
application to the substrate.

5800 Medium Strength Gasketing Sealant

LOCTITE® 5800 is a single component, medium strength, anaerobic sealant which cures when confined in the absence of air between close fitting metal surfaces. Typical applications include sealing close fitting joints between rigid metal faces and flanges. The product provides resistance to low pressures
immediately after assembly of flanges. Typically used as a form-in-place gasket on rigid flanged connections, e.g. gearbox and engine casings, etc.



Benefits:
• Leading in Health & Safety
• No hazard symbols, no risk phrases & no safety phrases
• “White” Material Safety Data Sheet – no entries in sections
2, 3, 15 and 16 of MSDS acc. to (EC) No. 1907/2006 – ISO
11014-1
• Excellent chemical and thermal resistance of cured product

Technical Data:
• Colour: Red
• Service temperature range: -50°C to +180°C
• Tensile shear strength: 12 N/mm²
• Max. gap: 0.3 mm
• Max Fixture time steel: 25min.
• Strength: Medium
• Cure method: Anaerobic
Pack size: 50ml

574 - General Purpose Flange Sealant

Conforms with BS6920 (potable water). General purpose flange sealant for gaps up to 0.5mm. Typical applications are hydraulic and pneumatic control valves, transmission and engine flanges and marine pipework.
Suitable for 90% of flange sealing applications.

511* - Thread Sealant

Seals and locks in any position. Low strength and easily dismantled. Contains teflon to prevent galling. *Fast cure version of 572. Conforms with:BS 6956 : 7 (gas). Crries the German DVGW approval. tested in accordance with EN751-1. Certified to NSF P1.