574 Flange Sealant

General purpose flange sealant for gaps up to 0.5mm. Typical applications are hydraulic and pneumatic control valves, transmission and engine flanges and marine pipework. Suitable for 90% of flange sealing applications. Carries the German DVGW approval. Test in accordance with EN751-1. certified to NSF P1.

572 - Thread Sealant - Coarse Threads - Slow Cure

Recommended for all coarse threads where slow cure is required to allow final adjustment before sealing. Meets BS 6956 Type A for sealing gas fittings. WRC approved for use with potable water.

574 Flange Sealant

General purpose flange sealant for gaps up to 0.5mm. Typical applications are hydraulic and pneumatic control valves, transmission and engine flanges and marine pipework. Suitable for 90% of flange sealing applications. Carries the German DVGW approval. Test in accordance with EN751-1. certified to NSF P1.

Loctite Gasket

Loctite 5188 has been designed to function in the most demanding applications with superior adhesion and flexibility, even after heat ageing. Loctite 5188 takes anaerobic gasketing to a new level. Typical applications include metal to metal assemblies of machined flanges such as gearboxes, housings, covers, etc.

5188 Highly Flexible Anerobic Gasket 50ml

Activators for Thread & Gasket Sealants

7649N - Recommended for use when a very fast cure is required. 7471T - Recommended for use at below 15C or on inactive surfaces.

5800 Medium Strength Gasketing Sealant

LOCTITE® 5800 is a single component, medium strength, anaerobic sealant which cures when confined in the absence of air between close fitting metal surfaces. Typical applications include sealing close fitting joints between rigid metal faces and flanges. The product provides resistance to low pressures
immediately after assembly of flanges. Typically used as a form-in-place gasket on rigid flanged connections, e.g. gearbox and engine casings, etc.



Benefits:
• Leading in Health & Safety
• No hazard symbols, no risk phrases & no safety phrases
• “White” Material Safety Data Sheet – no entries in sections
2, 3, 15 and 16 of MSDS acc. to (EC) No. 1907/2006 – ISO
11014-1
• Excellent chemical and thermal resistance of cured product

Technical Data:
• Colour: Red
• Service temperature range: -50°C to +180°C
• Tensile shear strength: 12 N/mm²
• Max. gap: 0.3 mm
• Max Fixture time steel: 25min.
• Strength: Medium
• Cure method: Anaerobic
Pack size: 50ml

542 Hydraulic Sealant

Medium strength, medium viscosity. Impervious to all common hydraulic fluids including fire resistant synthetics. Will not clog valves or fine filters. Replaces tapes, pastes and self-sealing compression joints.
Recommended for threaded fittings as used in hydraulic and pneumatic installations.
Medium threadlocking strength.
Suitable for high pressure systems.
Temperature range: -55C to 150C

510 - Flange Sealant

Recommended for high temperature applications (up to 200C), where maximum solvent resistance is required.
AGA approved No. 2590 up to 6900kPA (100psi).

510 - Flange Sealant

Recommended for high temperature applications (up to 200C), where maximum solvent resistance is required.
AGA approved No. 2590 up to 6900kPA (100psi).

542 Hydraulic Sealant

Medium strength, medium viscosity. Impervious to all common hydraulic fluids including fire resistant synthetics. Will not clog valves or fine filters. Replaces tapes, pastes and self-sealing compression joints.
Recommended for threaded fittings as used in hydraulic and pneumatic installations.
Medium threadlocking strength.
Suitable for high pressure systems.
Temperature range: -55C to 150C