Copely Industrial Layflat Hose

LH Series
Light duty blue industrial layflat - LH series. General-purpose hose especially suitable for drainage of locations with relatively small differences in elevation; for temporary water supply: for sprinkler irrigation or due to its resistance to most chemicals, for spreading liquid fertilisers and agricultural chemicals. Colour Blue.

Special features:
Made from cadmium free materials.
Resistance to a wide range of chemicals.
Silicone free.
Abrasive resistant.
Good flexibility.
Long service life.
Minimal electrical conductivity.
Tough, puncture-proof.
Fast transfer of liquids.
Unaffected by the elements.
Operating temperature: -25C/60C.
Supplied in 10 metre coils.

Light Duty Blue

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female DIN, O-Ring Swivel. 34° Cone - Heavy Series, 90° Swept Elbow

Drop dimensions meet ISO 12151-2.

Bosch Rexroth Pneumatic Fittings

AS3-MBR Series Air Regulator Mounting Plate for use with Rexroth AS3 series air preparation units.

For further specification on this product please see the attached PDF under the additional information tab.

AS3-MBR Series Air Regulator Mounting Plate

For further specification on this product please see the attached PDF under the additional information tab.

Kennedy® Mini ISO Magnetic Cylinders

According to the European Standard CETOP RP52-P and DIN/ISO 6432. Fixed mechanical cushioning has been fitted as standard in order to reduce wear by high impact loads at very high speeds. Flanged construction. Operating temperature: 0°C - 80°C (with dry air -20°C). No Load Speed: 10 - 1000mm/sec. 1 - 10bar Pressure.

Series R3M - Double Acting

PCL? InstantAir Airline Couplings

The InstantAir range of couplings and adaptors are the original and genuine Broomwade bayonet fittings. Steel bayonet type couplings, preventing accidental disconnection Suitable for most fixed compressed air applications, although swivel adaptors are recommended for hose applications.
Nominal bore: 5.6mm.
Maximum flow rate: 54 cfm 100 lbf/in.
Maximum working pressure: 17 bar (250 lbf/in).
Temperature range: -20C to 80C.



1/4" BSPT.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Pipe Inserts

Available in 10mm, 15mm and 22mm.

SMC One-Touch Mini Male Adaptor

KJL
Use to pipe at right angles to female thread. Most general
style.
KJL04-M3: Tube O.D. 4mm. Thread T: M3 x 0.5.
KJL04-M5: Tube O.D. 4mm. Thread T: M5 x 0.8.
KJL06-01S: Tube O.D. 4mm. Thread T: R1/8.
KJL06-M5: Tube O.D. 4mm. Thread T: M5 x 0.8.

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RXS Series X-Plug Connector Pneumatic Fitting

Standard Metric M5-G X-Plug Connector push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Push-Fit Pneumatic Fittings

Quick and simple tube insertion. Compact lightweight design with a well proven tube retaining system. Tapered threads have a re-usable thread seal and parallel threads have a rubber washer.
Main body manufactured from nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar.
Pressure range: - 0.9 bar min to + 10 bar max.
Temp range: - 20C min to + 70C max.
Tube suitability: nylon, polyurethane.

KQ2H04-01S: Tube O.D. 4mm. R 1/8.
KQ2H04-02S: Tube O.D. 4mm. R 1/4.
KQ2H06-01S: Tube O.D. 4mm. R 1/8.
KQ2H06-02S: Tube O.D. 6mm. R 1/4.
KQ2H06-03S: Tube O.D. 6mm. R 3/8.
KQ2H08-01S: Tube O.D. 8mm. R 1/8.
KQ2H08-02S: Tube O.D. 8mm. R 1/4.
KQ2H08-03S: Tube O.D. 8mm. R 3/8.
KQ2H10-01S: Tube O.D. 10mm. R 1/8.
KQ2H10-02S: Tube O.D. 10mm. R 1/4.
KQ2H10-03S: Tube O.D. 10mm. R 3/8.
KQ2H10-04S: Tube O.D. 10mm. R 1/2.
KQ2H12-02S: Tube O.D. 12mm. R 1/4.
KQ2H12-03S: Tube O.D. 12mm. R 3/8.
KQ2H12-04S: Tube O.D. 12mm. R 1/2.
KQ2H16-03S: Tube O.D. 16mm. R 3/8.
KQ2H16-04S: Tube O.D. 16mm. R 1/2.

Equal Tee Connectors