SMC Rotary One-touch Fitting Male Elbow Adaptors

KSL (Standard)
KSL06-01S: Tube O.D. 6mm. RPM: 500. Thread: R1/8.
KSL08-01S: Tube O.D. 8mm. RPM: 400. Thread: R1/8.
KSL08-02S: Tube O.D. 8mm. RPM: 400. Thread: R1/4.

Series S6520

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Male Stud Swivel Elbow

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female DIN, O-Ring Swivel, 24 Cone - Light Series

Type FDLORX

SMC FRL Accessories



Set Nut

Set Nuts

SMC One-Touch Mini Plug-in Reducer

KJR
Use to change size of One-touch fittings.
KJR04-06: Tube O.D. 4mm x fit dia 6mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Type 2 Conical Silencer Sintered (with Hex)

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female DIN, O-Ring Swivel, 24 Cone-Heavy Series

FeType FDHORX

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Stem Elbows

Designed to simplify pipe connection in restricted spaces. The Speedfit Stem Elbow provides an instant swivel fitting so pipe can be orientated in any direction. Provides a swivel type connection. Suitable for central heating systems. A special 10mm version gives a neat connection from concealed plumbing to a radiator.

Kennedy Air Lube Oil

Excellent air release quality, low foaming ability and resists clogging. Contains anti-rust and anti-wear additives. Extremely resistant to water absorption and can be mixed with all mineral oil-based lubricants without draining the system. Can be used on all air tools. ISO Grade VG22.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

'Y' Reducer