Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Tees

Connects plain pipe end to end and at 90.

Brass Wing Back Elbows

Suitable for central heating systems Manufactured in DZR Brass.

Manually Operated Slide Valve

Aluminium body, stainless steel spool, NBR seals.
Ports: G1/8 – G3/4
Fluid: Filtered air, without lubrication. If lubricated air is used, it is recommended to use ISO VG32 oil. Once applied the lubrication should never be interrupted.



Type: Female/Female
Connection: 3/8

Crimper

Powerful, lightweight, portable hand crimper. Crimps 1? spiral no skive couplings
Crimps 1? wire braid no skive couplings.
Ideal for small workshops & mobile vans Full validated crimp settings.

Portable Coupling Crimper - MCX20-HP

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Stem Adaptors

For use with other fittings, converts plain end pipe into male thread.

Camozzi Female/Female Reducers

2553
Series 2000 pipe fittings BSP adaptor female reducer.
Available in threads:
G1/8 - G1/4 overall length 17mm.
G1/8 - G3/8 overall length 18mm.
G1/4 - G3/8 overall length 19.5mm.
G1/4 - G1/2 overall length 23mm.
G3/8 - G1/2 overall length 24mm.

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2080 Series

Gates Hydraulic Couplings

Female SAE, Flat Face O-Ring Swivel,
90° Swept Elbow, Heavy Series.

SMC Plug Connectors

KQ2P

KQ2P-04: Fit dia: 4mm.
KQ2P-06: Fit dia: 6mm.
KQ2P-08 Fit dia: 8mm.
KQ2P-10: Fit dia: 10mm.
KQ2P-12: Fit dia: 12mm.



Colour: white.