PCL "Schrader" Heavy Duty Airline Coupling Adaptors

Case hardened, zinc finish. For use with 'Schrader' type couplings.

Integral Tailpiece (non-threaded)

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female DIN, O-Ring Swivel, 24 Cone-Heavy Series

FeType FDHORX

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Straight Tap Connectors

With brass swivel nut and sealing washer. Suitable for central heating systems.

Exhaust Restrictors with Silencers

Superior sound reduction. Cylinder speed easily set. Retainer prevents accidental loss of needle.

Pressure Line Filter Elements

The selection of the perfect filtration solution contributes significantly to prevent damage caused by contamination whilst increasing productivity and reducing maintenance costs. The new filter element technology used in Betamicron4, has been specially developed to ensure sensitive components are protected, whilst the filter element has a significantly longer service life providing a high level of cleanliness and long-term stability for your hydraulic or lubrication systems.

Type D/DN - Pressure Line Type

Camozzi Swivel Branch Tees

S6430
Super-rapid fittings for plastic tubes. Push-in fitting swivel branch Tee.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
12mm tube - G1/4 thread.
12mm tube - G3/8 thread.
12mm tube - G1/2 thread.

Series S6440

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Swivel Run Tees

U7K

Solenoid valves are used in fluid power pneumatic and hydraulic systems, to control cylinders, fluid power motors or larger industrial valves.

Nominal dimensions: 22 x 22.
Protection class: IP54 - DIN 40050.
IP65 (with connector Mod. 122-800).
Insulation: Class H (180C).
Connections: bipolar plus earth DIN 43650 (version B).
Protection: U70PET G7PA.



PET: U7K
PA: G7K
110V 50/60Hz 4,3VA
125V 50/60Hz 5.5VA

Camozzi Extended Swivel Elbows

7526
Super-rapid contact fitting Technopolymer extended swivel elbows with O-ring assembled.
Available in:
4mm tube, G1/8 thread.
6mm tube, G1/8 thread.
6mm tube, G1/4 thread.
8mm tube, G1/8 thread.
8mm tube, G1/4 thread.

Kennedy® Air Lubricator Units

Adjustable, constant oil flow. Integral mounting provision. Use individually or as part of a combination unit.
Temperature range: -10°C to +60°C.
Max input pressure: 10 bar.
Body: Technopolymer.
Bowl: Polycarbonate with protector.
Recommended oil: ISO VG32 (Servo System 32).