Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Pipe Inserts

Available in 10mm, 15mm and 22mm.

Series 2013

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Female - Female Elbows

Hydraulic Couplings

A range of one piece, no weep couplings covering a huge range of styles and terminations. Patented 'C' insert ensures an evenly distributed crimp. One coupling can be used with 1-wire and 2-wire hoses of various outside diameters. Reduced stockholding for an easier to manage inventory.

Key features:
Revolutionary one-piece design.
"Leak-free" concentric insert.
Optimum insertion force.
Patented "C" insert "Bite-the-wire" crimp.
No - skive.

Female DIN, O-Ring Swivel. 34° Cone - Heavy Series, 90° Swept Elbow

Drop dimensions meet ISO 12151-2.

Brass Straight Adaptors

Suitable for central heating systems This fitting is made of the following components:- The body is produced in brass ?O?Rings are nitrile rubber The collet is produced in acetal copolymer with stainless steel teeth.

SMC Rotary One-touch Fitting Male Elbow Adaptors

KSL (Standard)
KSL06-01S: Tube O.D. 6mm. RPM: 500. Thread: R1/8.
KSL08-01S: Tube O.D. 8mm. RPM: 400. Thread: R1/8.
KSL08-02S: Tube O.D. 8mm. RPM: 400. Thread: R1/4.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Elbow Connector

TM Multi-tube Holder

The SNC TM tube holder is ideal for managing and arranging runs of tubing. It is easy to load and firmly holds tubing in place, the holders can be mounted in place with screws.
It is possible to cut the holder to your specific requirement.
Manufactured from flame resistance resin.

Suitable for use with Nylon, Soft nylon and Polyurethane tubing.



Temperature range: -20C to +60C.
Colour: Black.

Series AF

Part of SMC's new modular FRL system. Integral water separator. New super efficient 5um poly-element.

Replacement filter elements and mounting brackets are also available.

B - Bracket
C - Autodrain
D - Autodrain

Air Filters

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Male Taper

SMC Pneumatic Fittings

The VQ20/30 series is a pilot operated, two port multi-media valve. The series is compact and lightweight with a large flow capacity. The VQ20/30?s long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.

VQ20 Series 2 Port Solenoid Valve, Pilot Operated

Series: 2(VQ21)
Body Style: A (single unit)
Coil Voltage: 5 (24V DC)
Lead Wire: Y (DIN Terminal)
Voltage Protection: Z (Light & Surge Suppressor)
Port Size: C8
Option: F Bracket