Series 61 Aluminium Profile Cylinders

Double Acting.
Standard DIN/ISO 15552.
Stainless steel piston rod.
Anodised aluminium extrusion cylinder barrel.
Cast aluminium End Blocks.
Stroke min-max lengths: 10-1000mm.
Bore sizes: Ø 32, 40, 50, 63, 80, 100, 125mm.
Operating temperature: 0°C to +80°C (with dry air -20°C to +80°C).
Operating Pressure: 1 to 10 bar.
Speed: 10 to 1000mm/sec (no load).
Connections: Ø 32 – 1/8”, Ø 40, 50 – ¼”, Ø 63, 80 –3/8”, Ø 100, 125 – 1/2”.

Auto-Switches

Auto Switches

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

Rexroth QR1-RAI Series Female Straight Pneumatic Fitting

Standard Metric M5-G Female Straight push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Stop Ends

Produces a permanent leak-proof seal, but can also be removed to allow extension to the system.

Camozzi Tube To Tube Couplings

6580
Super-rapid fittings for plastic tubes. Push-in fitting tube to tube connector.
Available in 4mm, 6mm, 8mm, 10mm and 12mm tubes.

Equal Tube Tees
Series 6540

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

In-Line flow Restrictor

Pressure Line Filter Elements

The selection of the perfect filtration solution contributes significantly to prevent damage caused by contamination whilst increasing productivity and reducing maintenance costs. The new filter element technology used in Betamicron4, has been specially developed to ensure sensitive components are protected, whilst the filter element has a significantly longer service life providing a high level of cleanliness and long-term stability for your hydraulic or lubrication systems.

Type D/DN - Pressure Line Type

Pressure Line Filter Elements

The selection of the perfect filtration solution contributes significantly to prevent damage caused by contamination whilst increasing productivity and reducing maintenance costs. The new filter element technology used in Betamicron4, has been specially developed to ensure sensitive components are protected, whilst the filter element has a significantly longer service life providing a high level of cleanliness and long-term stability for your hydraulic or lubrication systems.

Type D/DN - Pressure Line Type

Camozzi Male Stud Couplings

S6510
Super-rapid fittings for plastic tubes. Push-in fitting-male stud.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
10mm tube - G1/2 thread.
12mm tube - G1/4 thread.
12mm tube - G3/8 thread.
12mm tube - G1/2 thread.