Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Equal Straight Connectors

Connects plain pipe end to end.

Series S7522

These new models have been released in technopolymer, maintaining the same technical characteristics as the existing Camozzi fittings range. Lightweight, adaptable and they allow for easy maintenance of the collet and the internal seal. All materials, except for the internal seal, can easily be recycled.

General Data
Tube external diameters: 4 - 6 - 8 - 10 - 12 - 16 mm
Connections: G1/8, G1/4, G3/8, G1/2, G3/4, M5, M7
Material body: technopolymer; insert: brass, collet: nickel-plated brass; seals: NBR
Threads GAS cylindrical ISO-228 (BSP)
Operating pressure min. - 0,9 bar, max. 16 bar
Tube to connect Rilsan, polyamide 6 - 11 - 12, polyethylene, PU
Diameters: 4 - 6 - 8 - 10 - 12 - 16 mm
Fluid compressed air (for other types of fluid, contact our engineers)
Temperature -20 ?C (see data for tubing used)



Male Swivel Elbow

Series 9 Manifold Bases
Size: 1
Type: 1 Single-sub Base - Side Outlets

Size: 1
Type: 1 Single-sub Base - Side Outlets

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Tube suitability: Nylon, polyurethane.

Ball Valves - Female to Male

Push-fit System - Compressed Air

Range of push-in fittings and pipe provide the ideal connection from compressor to air-line service components through to complete ring main and take off points. A compressed air system can be installed quickly and easily, reducing the need for specialist staff providing reduced production down time. All the connections can be made with a simple push-in action, no need to prepare threaded pipe or solvent. The system will be ready for use immediately and complex systems much more rapidly than traditional methods. Because of the ease of use, this system can be disconnected, altered and extended. Suitable for use with a wide range of plastic and soft metal pipes including UPVC, ABS, polyethylene, nylon, mild steel and copper. It is recommended that all installations are checked prior to use to determine that a seal has been made. The maximum torque figures quoted are dependent on the mating thread conforming to the relevant British or International thread standard.
Working Temperature Range
Minimum Working Temperature -20C
Maximum Working Temperature +70C
Working Pressure
Temperature Pressure
+23C 10 Bar
+70C 7 Bar

Plug

Compressed air fitting.
This fitting is made of the following components:-

The entire body is produced in acetal copolymer

SMC One-Touch Union Y-Connectors

KQU
To branch tubing in the same direction. Colour: black.
KQU04-00: Tube: O.D. 4mm.
KQU06-00: Tube: O.D. 6mm.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Straight Connector

Camozzi Extended Swivel Elbows

7526
Super-rapid contact fitting Technopolymer extended swivel elbows with O-ring assembled.
Available in:
4mm tube, G1/8 thread.
6mm tube, G1/8 thread.
6mm tube, G1/4 thread.
8mm tube, G1/8 thread.
8mm tube, G1/4 thread.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Elbow Connector to Male Taper

Series AF

Part of SMC's new modular FRL system. Integral water separator. New super efficient 5um poly-element.

Replacement filter elements and mounting brackets are also available.

B - Bracket
C - Autodrain
D - Autodrain

Air Filters