Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Bulkhead to Female Parallel

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Branch Tee to Male Taper

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Reducer Stem

Base Mounted Solenoid Valves

IP67 base mounted valves. Easy to expand manifolds. Cassette and tie rod manifold construction. Wide choice of serial transmission options. Dual three port valve bodies available.

Rexroth Standard Blanking Plugs

QR1-RDS Series
Pin bushing blanking plug.
Available in diameters: 4, 6, 8, 10, 12 and 14mm.

Ambient temperature min/max: +0°C/+60°C.
Working pressure min/max: -0.95 bar/10 bar.
Housing material: Polybutyleneterephthalate.

Dies to suit MCX20-HP

Product Number: 8000-10197
For hose size 1.1/4".

Copely Polyurethane Tube

CPU Series
Codeflex polyurethane tube is suitable for a wide range of applications demanding a flexible and cut resistant tube in applications such as pneumatic control systems and chemical transfer tubing. Codeflex polyurethane is well suited to applications demanding maximum kink resistance, minimum kink memory. It is suitable for fitting into confined spaces where conventional tubes lacking the above factors would increase fitting time in addition to flow restriction.

Applications:
Pneumatic control systems.
Fuel and lubrication lines.
Chemical transfer tubing.
Special features:
Exceptional abrasion resistance.
Resistance to a wide range of chemicals.
High flexibility.
Silicone-free.
Working pressures:
Nominal working pressure calculated at 23C with a 4.1 safety factor.
Temperatures: -50C/55C (short term use at 85C).
Special note:
The CPU series has been designed and developed to meet the exacting standards of the push fit type of coupling.
Supplied as 30 metre coils.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Reducing Tees

Connects plain pipe end to end and smaller diameter pipe at 90.

Pressure Line Filter Elements

The selection of the perfect filtration solution contributes significantly to prevent damage caused by contamination whilst increasing productivity and reducing maintenance costs. The new filter element technology used in Betamicron4, has been specially developed to ensure sensitive components are protected, whilst the filter element has a significantly longer service life providing a high level of cleanliness and long-term stability for your hydraulic or lubrication systems.

Type R - Return Line Type

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

3030 Series