Kennedy Torque Wrenches

Kennedy?s fixed torque wrenches have been designed for use on production lines and for other applications where a specific torque is required for repetitive operations.

Fixed Head Torque Wrench

Features include:

Chrome plated, polished steel head.
Retractable torque setting lever.
CLICK & SNAP action indicates when the pre-set torque level has been reached. Four easy read scales N.m, kgf.m, lbf.in x10, lbf.ft
Push through square drive connector to instantly reverse action.
Knurled grip plastic handle.
Complete with factory tested calibration certificate, operating instructions and torque conversion chart.
Supplied in blow moulded cases, except FTW800, which is in a cardboard case.
Manufactured to ISO 6789 : 1992 (BS EN 26789 : 1994).
Accuracy plus/minus 4%.

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

Dial Indicating Torque Drivers

Can indicate torque in two ways - measures and displays torque as it is applied, or measures and displays the maximum torque used, after it has been applied. Ideal for the electronics, electrical and domestic appliance industries. Stainless steel shafts coloured aluminium handles and scaled nylon dials. 1/4" Hex drive. Dual scale. Manufactured to ISO6789:1992.

Standard Type

Torque Range: 50-250 cNm 4-20Ibf.in
Can be used with 1/4" drive. Sliding ?T? bar supplied.

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

16mm Spigot End Fittings

Metric

Flare End

Classic Mechanical Torque Wrenches

Ideal for use in noisy environments. The torque build up can easily be recognised by three signals: Sight - see the wrench start to break; Touch - feel the point of torque; Sound - the ratchet 'click'. Hard wearing mechanism retains +/- 3% accuracy for up to 10,000 operations. Push through square drive connector for instant direction reversal. Easy to read permanent scale with large clear markings that are branded into the handle. Retracting torque adjuster that cannot be altered by accident ensuring accuracy on repetitive operations.

1/2" Square Drive

Torque Range: 70-330Nm 10-250Ibf/ft

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

16mm Spigot End Fittings

Inch

Open End

Tri-Torq Torque Wrenches

Tri-Torq wrenches are a unique triangular handle design linear torque wrench, once the preset torque has been reached an audible "CLICK" is emitted. Manufactured from high quality satin finish steel with a polished steel head.

Conforms to BS EN 26789 : 1994 and Federal GGG-W-686 standards.

FXL300 1/2" Drive 60-320Nm Torque Wrench

Torque Range:
60-320Nm/45-235ibf ft

Norbar Torque Wrenches

All Norbar torque wrenches are designed and manufactured to exceed the following national and international standards: BS6703: 1988, ISO 6789: 1992 & U.S.A.GGG-W-00686-C (GSA-FSS).

16mm Spigot 'P' Type (Pre-set)

Designed for the production environment where they will be set and then dedicated to a particular application. There is no scale, the wrench must be set against a Torque Wrench Analyser or similar instrument. Setting system is designed to discourage unauthorised alteration. Coloured end seals are provided to identify the wrench to a particular operator, torque setting or calibration period.

Torque Range: 20-200Nm 15-150ibf.ft

For further specification on this product please see the attached PDF under the additional information tab.

Standard Series Torque Multiplier

The 'Standard series' torque multiplier has been designed for the specialist user where it is necessary to provide higher torque than would otherwise be possible due to limitations on space or operator strength. This series employs multiple stage epicyclic gearing to give a wide range of torque outputs and ratios to suit most applications. The torque multiplication is accurate to more than plus/minus 4% with a maximum output of 47,500Nm. *Models contain the AWUR 'anti wind up ratchet' mechanism. As with any high ratio gearbox (25:1 or more) a certain amount of wind-up (spring) has to be taken up before any useful tightening work can be applied to the nut. Each time the input device is released, the wind-up will rotate back against the direction of operation.The AWUR mechanism retains all of the wind up forces as they are created locking the multiplier onto the nut being tightened. This means that even when used upside down the multiplier will support it's own weight.



Torque Range: 3400Nm 2500 Ibf.ft
Square Drive: 3/4 '' Input 1'' Output

For further specification on this product please see the attached PDF under the catalogue PDF links tab.

TorqueVario-S torque screwdriver set 13 pieces.
1.0 to 5.0Nm range with step-less adjustment set via the window scale.
Ergonomic SoftFinish grip for comfort during repetitive tasks.
Light, compact, modern design.
Calibrated, certified and traceable to EN 6789 with an accuracy of +/-6%.

Also compatible with Wiha’s one piece torque blades for unrivalled access in tight spaces.

Kit Contents:
Metal box with cut-foam insert contains TorqueVario-S torque screwdriver, setter, bit holder and 10 of ¼” bits.
Phillips PH1 PH2, Pozi PZ1 PZ2, Torx T10 T15 T20 T25, Hex 3mm 4mm.

26893 Engineer's Torque Screwdriver Set

BH25 Torque Breaking Handle

Handle 'breaks' at an angle of 20 and features a unique patented single direction mechanism, ensuring long tool life and repeatable accuracy. Fitted with the new mechanical torque adjustment locking device. Automatically resets when force is released and returns to the inline position. Compatable with Norbar® 16mm spigot end fittings
Torque range: Nm 5.0 - 25. Ibf.in 44 - 221.
Spigot size: 16mm (5/8`).
Overall length: 265mm.
Weight: 415g.