DCGX

Suitable for External/Internal Toolholders

DNMG

Suitable for External/Internal Toolholders.

Carbide Grade AC2000 (P15 - P30)

Al2O3 Coated Grade
For general to rough cutting of steels.

NSU Chipbreaker

Application: finishing ~ light cut.

KNUX

Suitable for External Toolholders.

DNMG Indexable Turning Inserts

QX535S (ISO M10-M30) CVD Coated. For roughing and finishing turning applications on a wide variety of Stainless Steels.

Iscar Parting and Grooving Blades

TGFH/R/L Blades with Tangentially Oriented Pocket for Parting and Grooving, for TANG-GRIP Single-Ended Inserts.

TGFH/R/L Parting and Grooving Blades

Sumitomo T-Rex Carbide Inserts

The Sumitomo T-Rex can replace your costly DNMG applications with the economical T-REX System!

Features & Benefits
55 triangle insert.
6 cutting edges versus the standard 4 edges of a DNMG insert.
Rigid clamping system ensures accurate insert indexing.
Up to 2.5mm (0.100") depth of cut.
Available in the -LU and ?GU chipbreakers with grades AC700G, AC2000 and AC3000.
Suitable for all steels including stainless.

T-Rex TRM55 Carbide Insert

Chip Breaker:
LU Type Finishing Breaker
DOC 0.25mm-1.75mm
Fz 0.025-0.4mm/rev

Grade Description: AC700G (Steels) New carbide grade for higher speeds and light cuts with dry machining capability and long tool life.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance.

CNMG

QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.

Yamaloy® Indexable Carbide Inserts

Grade description: QZ830 (ISO P25-P40) Tough coated grade for Steels, suitable for interrupted cutting such as cross holes.

WCMX Carbide Insert

Suitable for Indexable Drills