VBMT Indexable Turning Inserts

T9025 (ISO P20-P30, M20-M30) MT-CVD coated. Increased wear resistance provided by the new ?Double-Bridge? coating technology allowing for higher cutting conditions. Universal grade for medium to rough turning of steel at medium speed. PS-Finishing to medium operation chipbreaker.

CNMG

Suitable for External/Internal Toolholders

VBMT

Suitable for External Toolholders.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-C Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-J/JS Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Designed for machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds, interrupted cut and unfavourable conditions. Excellent notch wear and built-up edge resistance.

Dijet and Indexa Seiki? Toolholder and Insert Sets

This set contains an Indexa Seiki? SCLCR boring bar and 10 Dijet CCMT inserts.

SCLCR Boring Bar and Insert Set

This Dijet and Indexa Seiki? Toolholder and Insert Set consists of 1x SCLCR screw on style boring
bar and 10x CCMT inserts.
S08K SCLCR 06 - Right Hand
95 approach for 7 positive.
80 rhombic inserts.
0.05 - 0.3mm/rev.
D.O.C.: 0.25 - 2mm.


Grade description for Dijet JC215V: (ISO P10-P40 K25-K40).
On the weather-resistance and tougher base material, multi-thicker coating are adopted. This grade shows twice better tool life as conventional grade. Medium to high speed cutting for steels and medium speed cutting for cast iron. UT - With a low feed rate and small depth of cut, excellent metal removal can be obtained. Reduces the cutting force and prevents the excessive built-up edge in cutting mild steels, low carbon steels and alloy steels.

Iscar Turning Inserts

IC9150 Grade description: (P10 - P30, K10 - K25).
A TiCN/Al2O3/TIN multilayer, CVD coated grade. Used for finishing and medium machining of carbon and alloy steel and cast iron at high cutting speeds. High wear resistant and excellent repeatability.

TNMG

ISCAR Parting & Grooving Blades

ISCAR Tang-Grip? uses a single-ended insert for parting, with a revolutionary clamping method (patent pending). Very rigid clamping is achieved in a tangentially oriented pocket. This increases pocket life by 3 times more than any other SELF-GRIP mechanism.

Tang-Grip? TGFH Parting & Grooving Blades

ISCAR Tang-Grip? has the following features:

? Enables machining at high feed rates and provides excellent straightness and surface finish.
? Provides a solution to the problem of inserts being pulled out during retraction. Has a solid stopper, unlike the friction retaining force in the current systems. (Especially important on machines with a bar feeder or sub spindles.)
? In the SELF-GRIP? system the machining forces are exerted on a very short stopper, while in the TANG-GRIP system, machining forces are supported by a long and rigid rear wall. Pocket wear, which occurs during machining and insert indexing in the SELF-GRIP? system, causes a reduction in the clamping force. This does not happen with the new TANG-GRIP? system.
? The TANG-GRIP? system provides very accurate grooving repeatability.
? The combination of tangential clamping and free chip flow results in improved tool and pocket life.
? Offers a free, unobstructed chip flow. This is very important in deep grooving, since there is no upper jaw to interfere as in the other clamping systems.

For all technical specifications and inserts please refer to our catalogue.

WNMG Indexable Turning Inserts

QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.



Suitable for Internal/External Toolholders