Tuffsafe Fall Arrest Equipment

Trauma suspension straps are simple and easy to use and can fit all Tuffsafe harnesses. They allow the worker to stand up in their harness to ease the discomfort whilst suspended from a lanyard after a fall. Helps release the tension within the harness straps to relieve pressure on the groin which helps prevent loss of circulation to the legs and feet.
Prior to use attach one pack to the outer side of each leg strap. In the event of a fall unzip the pouches to release the straps and thread the plain end through both chrome rings and back through only one and pull tight to form a loop approx shin height. Stand up slowly on the straps and the discomfort will be relieved.
Lightweight and unobstructive.
Weight: 150g

TSTSS Trauma Suspension Straps

Ridgegear Harness Restraint Kit

RGHK5 IPAF
This kit is approved to the requirements of the IPAF technical guidance notes TGN H1/05/05. Each complete kit consists of a full body harness RGH 2 and a fully adjustable restraint
lanyard, the lanyard is supplied with a screw gate Karabiner.
To EN361 and EN354.

Features:
Weight: 1.15kg hHarness only.
Front & rear attachment point, rip stitch indicators. Lightweight & water resistant webbing.
Tough plastic container.

Tuffsafe Fall Arrest Equipment

"Soft Edge" 32mm wide, cut resistant polyester webbing provides greater strength and resistance along with it"s water repellent coating can help prolong it"s life. Lightweight, durable and fitted with a shock absorber pack and a 70mm delta link.
Max arrest force 6KN
Weight: 0.60kg

Certified to:
CE 0320
EN 364
EN 355

Australian Standard: AS/NZS 1891.1:2007

TSSA1 1.3m Shock Absorbing Lanyard - with Karabiner Hook

Tool Lanyard Loops

3103
Three elastic lanyards that attach to the 3102 series lanyards.
Quick release buckle. Stretch cord surrounded by tubular nylon webbing. Lock stitching for extra security. Adjustable barrel lock. Hi-Vis lime.
Maximum safe working capacity: 2.27kg.

Front & Rear D Elasticated Harness

With the introduction of elasticated webbing on the leg & lower chest straps, the RGH9 harness provides additional comfort and support during use. Based on the RGH2, this RGH9 is also fitted with a rear D and a chest mounted front D. This harness can be used similar to the RGH1 (see data sheet), but has the added feature of the front dee ring to extend the working capability of the harness. Utilizing the front dee, the harness can be fitted with a rope and grab system (RGA12) for vertical fall protection when an operative is making repeated ascents or similarly, when restraint/work-positioning is needed in either the vertical or horizontal plane.

A variety of other devices can be used with the front dee ring, but please check for suitability.

In addition to the elasticated feature, the harness is fully adjustable and fitted with rip stitch indicators. The ring connection between the chest & the shoulder straps, ensure no stress loading when force is applied to the front dee ring.

Accredited to: EN 361.
Web Material: 45mm water repellent polyester.
Nylon/polyester elasticated leg straps.
Fittings: High tensile steel alloy & st/steel.
Weight: 1.25kg.
Features: Rear & front attachment point, rip stitch indicators.

Tool@rrest Tie Hooks - Large Locking Hook

Super duty, reusable locking tie hook for organizing and cinching hoses, cords, pipe, and almost anything else. Colour: Hi vis orange.

Specifications:
Large hook attachment with 360° swivel (1.5"/38mm).
Cable lock for security and increased load capacity.
Adjustable sliding belt lock mechanism.
High tensile strength, weather resistant Nylon 66.
Excellent resistance to oil, salt, solvents, and alkali.
Temp range: -40°-176°F (-40°-80°C).
Recommended load limit: 44lbs (20kg).

3 sizes available:
Short belt (30cm).
Medium belt (40cm).
Long belt (50cm).

Rescue Tripod

The RGR1 Rescue Tripod is portable, lightweight and is easy to erect on site. It has adjustable lower and middle legs at 80mm intervals to adapt and adjust to the most demanding surfaces and varying ground conditions. There are two additional anchorage points (SWL 200kgs each)on the underside of the head for additional primary/secondary systems. This unit has many applications such as confined access, entry, rescue, retrieval, manhole, silos & trenches, etc. The RGR1 is extremely versitile and is recommended for use with the side attachment of the RGR7 rescue winch and the RGR4 fall arrest & rescue recovery winch.

SiteSafe® Fall Arrest Harnesses

SiteSafe® fall arrest harnesses are certified to the highest safety standards (EN361) and are designed to fit the wearer comfortably without restricting their movement over extended periods of use.

SiteSafe® full-body harnesses distribute fall forces throughout the body, substantially reducing the chance of injury.

The full-body harness keeps the worker suspended upright in the event of a fall and supported while awaiting rescue. Fully adjustable designs so one size fits all.

The range includes: 1 & 2 point fall arrest harnesses.

BHP025 Full Body Fall Arrest Harness with Work Positioning Belt -2 Point Attachment

Two point full body harness manufactured from strong 45mm wide polyester webbing.
Lightweight, durable comfortable and easy to put on ideal for all day comfort and use.
Adjustable thigh and chest straps with metal buckles and back anchorage dorsal D-ring attachment.
Two point anchor straps for extra harnessing support.
Detachable work positioning belt with textile back support with adjustable strap with metal buckles and two D-rings.
Two polyester/plastic 90mm D-rings and clip attachment at the rear.
Capable of supporting up to 310lb
(22st/140.6kg).

Certified to: CE 0321
EN 358:1999 EN361:2002

15 mtr Wire Fall Arrest & Rescue Block

The RGA4 is a three way retrieval block fitted with an up/down winch mechanism and the standard fall arrest capability. This unit can be used as a standard fall arrest block, but in the event of a fall, the operative can be winched up or down to safety almost immediately. As most rescue systems lower the casualty, the RGA4 can raise the operative to safe area, if the area below is unsuitable.

The RGA4 can also be fitted to the RGR1 tripod for use in the confined access industry.

The Man-riding rescue retrieval winch function is for use only as a rescue provision & NOT for access / egress.
Where an operative is required to be lowered / raised for access / egress, then please use such equipment as the RGR7 50m Two-speed Man Riding RGR7 Winch.
This arrangement must be backed up with a independent separate fall arrest system, and a rescue provision that is also separate to the winch. Where a 15m maximum length is suitable the RGA4 / RGA4H can provide both fall arrest back-up as well as the rescue provision.
If the requirement is for more than 15m metres, please contact us for further details.

Accredited to: EN 360 & EN 1496 A&B
Cable spec: 15 x 5mm Galvanized Steel Wire Rope (Also available with stainless steel wire)
Connector: Double action. High tensile steel alloy
Weight: 11.35 kg
Features: Fall indicating connector. Retrieval system.
Size mm: L 340 x W 258 x D 80
Max Arrest Force: < 6 kN
Approx Arrest Dist: 0.5 Metres

Self Retracting Lifeline

Miller Falcon SRL; Self retracting lifeline with high impact-resistant nylon housing to withstand the harsh rigours of the toughest applications (Lifetime housing guarantee) and no annual factory re-certification is required - An authorised competent person can annually re-inspect the FalconTM SRL.