Sherwood Drills Taper Shank HSS

Suitable for single and multi-spindle drilling machines. The taper shank being the engineering industries recognised standard and most widely used method for holding and driving cutting tools. Manufactured to BS328;Part 1:1986, DIN345RN, DIN343RN.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT3) - Inch

Sherwood Reduced Shank Drills (Blacksmiths) - 1/2" Parallel Shank HSS

General-purpose drills for light duty work, for drilling steels, cast iron, nickel brass and graphite. Reduced parallel shank 1/2". Point angle 118, helix angle: normal, web thickness: standard, tolerance of diameter: h8, tolerance of shank: -0.01/0.08. Manufactured to BS328. Fracturing of the drill shank may occur if it is used for any other purpose or if extreme pressure is exerted on the drill.

For all dimensional specifications please refer to our catalogue.

Inch

All sizes will fit into a 13mm/1/2" chuck.

Pinzbohr Standard Boring Head Spares

To suit standard boring heads

Locking Screws

PSC and PSCa (adjustable) Collets for Plain Shank Cutters

Tru-Loc Collets are available for plain shank cutters in two different styles, PSC non adjustable and PSCa - Collets with an adjustable back-stop screw to allow more accurate & consistent cutter replacement.

For all dimensional specifications please refer to our catalogue.

PSC(a) Type

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood Stub Drills HSS

General-purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118, Helix angle: Normal, Web thickness: standard, Relief angle: 10-20, Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to BS328:Part 1:1986/DIN338.

Series S100

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap BSPF (British Standard Pipe Fine) Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.

Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Metric

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Number Sizes

Kennedy® 3 Flute 60° High Helix End Mills Weldon Shank Carbide

Suitable for the high speed machining of titanium inconel, stainless steel and steel alloys. Cutting diameter to h10. Shank diameter to h6. Dimensions to DIN.

Short Series 3 Flute High Helix - Metric