Indexa-Seiki? Lever Lock Cartridge Units

60 Approach for negative triangular inserts.

PTTNR Right Hand

Sumitomo T-Rex Carbide Inserts

The Sumitomo T-Rex can replace your costly DNMG applications with the economical T-REX System!

Features & Benefits
55 triangle insert.
6 cutting edges versus the standard 4 edges of a DNMG insert.
Rigid clamping system ensures accurate insert indexing.
Up to 2.5mm (0.100") depth of cut.
Available in the -LU and ?GU chipbreakers with grades AC700G, AC2000 and AC3000.
Suitable for all steels including stainless.

T-Rex TRM55 Carbide Insert

Chip Breaker:
GU Type General purpose Breaker
DOC 1mm-2.5mm
Fz 0.18-0.45mm/rev

Grade Description: AC700G(Steels)
New carbide grade for higher speeds and light cuts with dry machining capability and long tool life.

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Number Sizes

Swisstech 3 Flute Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 33 Regular SDN-3TR TiCN Coated

Dimensions to DIN 844.

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Long Series - Metric

Iscar Helido Indexable Endmills and Facemills

The new HELIDO H490 ANKX rectangular inserts have 4 helical right-hand positive cutting edges. They were designed in cutting edge lengths of 9, 12 and 17 mm. Insert construction is very thick and strong; clamped into a dovetail inclined pocket which provides a very rigid clamping and has a wiper which leaves an excellent surface finish.

Due to its strong construction, unique chip deflector with positive cutting angles and excellent grade combinations, this new family features high durability, low cutting forces and long tool life. Our most advanced SUMO TEC grades ensure excellent performance and reliability.

The new HELIDO tools can be used for machining steel, stainless steel and cast iron at very high machining parameters. HELIDO"s state-of-the-art of milling insert design, enables excellent performance and extremely high productivity.

H490 - A new family of double-sided inserts with 4 helical cutting edges.

For further specification on this product please see refer to our catalogue page.

H490 E90AX...-09 Indexable End Mills

End Mills with double-sided inserts, diameter range 16-40mm.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Tap Set UNF (Unified Fine) Straight Flute Ground Thread HSS

Each set of Sherwood taps contain one taper, second and plug lead tap:

Sherwood HSS Taper Taps are used to start cutting the thread. They are tapered back from the end 6 to 10 threads before a fully threaded diameter is reached. This allows the tap to be positioned easily and correctly before it starts to cut the thread.

The Second Tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before full thread diameter is reached.

The Plug Tap cuts threads to the bottom of a blind hole. It is only necessary to use the full set of taps when a blind hole is to be tapped.

Iscar Helido Indexable Endmills and Facemills

The new HELIDO H490 ANKX rectangular inserts have 4 helical right-hand positive cutting edges. They were designed in cutting edge lengths of 9, 12 and 17 mm. Insert construction is very thick and strong; clamped into a dovetail inclined pocket which provides a very rigid clamping and has a wiper which leaves an excellent surface finish.

Due to its strong construction, unique chip deflector with positive cutting angles and excellent grade combinations, this new family features high durability, low cutting forces and long tool life. Our most advanced SUMO TEC grades ensure excellent performance and reliability.

The new HELIDO tools can be used for machining steel, stainless steel and cast iron at very high machining parameters. HELIDO"s state-of-the-art of milling insert design, enables excellent performance and extremely high productivity.

H490 - A new family of double-sided inserts with 4 helical cutting edges.

For further specification on this product please see refer to our catalogue page.

H490 E90AX...-09 Indexable End Mills

End Mills with double-sided inserts, diameter range 16-40mm.

Starrett Holesaws

Starrett tungsten carbide tipped sheet metal holesaws are ideal for cutting high alloy and stainless steels, non ferrous light metals and reinforced fabrics. The tough tungsten carbide tipped teeth, have a positive cutting angle to provide fast and efficient removal of chips and swarf, cutting depth is 13mm.

Sheet Metal Holesaws Tungsten Carbide Tipped

Starrett tungsten carbide tipped sheet metal hole saws deliver the following advantages:
Ideal for production cutting.
Tungsten carbide tipped teeth provide superb product life and cutting performance.
High cutting accuracy.
Replacement pilot drills are available.
Complete assembly - there is no requirement to purchase a separate arbor and pilot drill.
Safety stop at the base of the hole saw prevents drilling beyond maximum cutting depth.
Cutting depth 13mm (1/2").

Sherwood Ground Flute Jobber Drill Sets HSS

Sherwood Jobber drills are general-purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite.

With precision-ground flutes and black finish (W-finish), this is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer.

Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Supplied in indexing metal cases. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN.

Ground Flute Jobber Drill 41 Piece Set HSS - Metric

Set contains: 6.0, 6.1, 6.2, 6.3, 6.4, 6.5, 6.6, 6.7, 6.8, 6.9, 7.0, 7.1, 7.2, 7.3, 7.4, 7.5, 7.6, 7.7, 7.8, 7.9, 8.0, 8.1, 8.2, 8.3, 8.4, 8.5, 8.6, 8.7, 8.8, 8.9, 9.0, 9.1, 9.2, 9.3, 9.4, 9.5, 9.6, 9.7, 9.8, 9.9 amd 10.0mm.