Guhring Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series 245 (MT3) - Metric

Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

HSS Threaded Shank Dovetail Cutters (Single Angle Cutters)

Designed to produce dovetail slideways in machine tool tables, jigs and fixtures. Bright finish, straight helix. Made to DIN1833. Shank to DIN 1835D.

45° Inverted - Metric (Form D)

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Short Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Inch

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.



BSF (Fine)

Sherwood Machine Reamers

Left hand spiral flute, right hand cutting. Manufactured to BS 122.

For all dimensional specifications please refer to our catalogue.

Inch

Dormer Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series A130 (MT1) - Metric

Allied Maxcut Thread Mills

The MaxThread™ threadmill range is manufactured from solid carbide with ground helical flutes and a TiAlN coating as standard. These product have been designed for the low volume/low cost production environment, providing excellent performance at a competitive price. A helical flute design has been maintained across the MaxThread™ range to allow
for maximum production benefits and to negate the need for straight flute thread mills. A comprehensive range of thread forms and technical information further supports the programme.

Features and Benefits:
Helical flute which offers increased strength and rigidity when cutting forces are applied.
TiAlN coated for increased tool life over uncoated tools.
Extensive range of thread forms.
High quality for consistent predictable production.

NPT Thread Mills

Solid Carbide Threadmills NPT TiAIN coated

Sherwood® Solid Carbide Drills

Sherwood Solid Carbide Stub Drills are suitable for drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard.

Solid Carbide Stub Drills

Indexa-Seiki? Indexable Boring Bars

Indexa-Seiki??s range of indexable tooling includes, face mills, end mills, boring bars and turning toolholders. All Indexa-Seiki? indexable tooling is manufactured to recognised ISO standards to ensure that the insert is clamped securely in the toolholder or milling body. The exceptional stability of Indexa-Seiki? indexable tooling when in operation, ensures you achieve the precision that you require in the finished component, every time.

Indexable tooling is the modern solution for all machining applications as the carbide inserts held in indexable tool holders can be changed as required to machine different types of material, many inserts have multiple cutting faces, once one face is blunt simply rotate the insert in the toolholder this flexibility helps to eliminate expensive down time and regrinding costs helping you to increase production and drive down running costs.

We are confident that from our selection of indexable toolholders, you will find the tool appropriate to the machining operation you are carrying out.

A full range of spares are readily available for all Indexa-Seiki? Indexable Tooling, please refer to our catalogue for details.

For all technical and dimensional specifications please refer to our catalogue.

SCLCR Through Coolant Boring Bar