Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with a Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Flute for threading blind holes.
Taper lead to DIN form C.
Tapping tolerance to 6H.
Max Depth 2.5 x D.
Helix angle 48.

For all technical and dimensional specifications please refer to our catalogue.

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 3.0-26.
(D)41mm x (L)46mm.

ER40

Kennedy Precision Hand Files Industrial Quality

Parallel edges, surfaces tapered towards end. Narrow version of hand file. For use where access is restricted. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Pillar

Available in Cut 0, 2 and 4.

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Kennametal Face Milling

Kennametal Dodeka™ inserts and cutters are for demanding face-milling applications in steel, stainless steel, cast iron, ductile iron, and other materials. They have been engineered to deliver higher cutting speeds and feed rates along with extended tool life. This has resulted in improved cutting performance and productivity across the most demanding of materials.

Compared to competitors' face-milling inserts, Dodeka inserts provide up to 30% more cutting performance at the same level of power consumption. At the same cutting conditions, Dodeka inserts supply up to 50% longer tool life.

With 12 cutting edges per insert, the unique Dodeka geometry generates low cutting forces, resulting in increased performance per edge. The inserts are also designed for ease of use, with a single screw for insert changing and indexing.

Dodeka™ Face Mills

Kennametal Dodeka™ Face Mills are specifically engineered to deliver consistent performance in demanding rough and finishing face milling applications!
Use less horsepower - and gain up to 30% in productivity.
Up to 50% longer tool life.
Easy-to-use - one screw enables fast, accurate indexing.
12 true cutting edges lower your cost per edge.
Run at higher speeds and feeds - with higher metal-removal rates.
Three new cutter sizes and three new geometries, including a new Wiper insert.
Engineered for applications requiring higher cutting speeds and feed rates with low cutting forces.
Ideally suited for roughing and finishing face milling applications in the General Engineering and
Automotive industries.
4.5mm depth-of-cut capability.
Available in diameters from 40 - 315mm.
Through-coolant standard.


For all technical specifications and inserts please refer to our catalogue.

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Rectangular Inch

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.



BSF (Fine)

Swiss+Tech® HSS "Orange Ring" Taps

Manufactured to DIN 371/376.

Spiral Point - HSS-PM Nitride and Oxide Finish ISO Metric Coarse

For through holes. Taper lead to DIN form B (4.5 x P) Tapping Tolerance to 6HX 2BX.

Indexa-Seiki MT-Morse Taper Adaptors

With internal morse taper socket. For use on drilling machines etc. For drills, core drills, reamers etc. Manufactured to stringent quality standards.



To DIN69871/A

Sherwood Long Series Drills HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328:Part 1:1986, DIN340RN, ISO494. Bright finish; drills are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Bright finish.