Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Brazed Tip Cranked Turning & Facing Tools

Right Hand. Available in Grades P40, P30 and K20.

Swiss+Tech 2 Flute Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 30 Long SDN-2TL TiCN Coated

Dimensions to DIN 844.

Kennedy Needle Files Industrial Diamond-Coated 16cm

Available in seven shapes, Hand, Half Round, Three Square, Round, Square, Knife and Flat and two grain sizes, 120/140 and 325/400 offering the solution to finishing problems where material hardness makes conventional files ineffective. Plated with finely selected diamond powder, 120 - 150 mesh. Can be used on tungsten carbide, ceramics, carbon, glass, fibreglass and hardened steels such as stainless steel, nimonics, titanium etc.

Knife

Taylor & Jones Expanding (Re-grindable) Machine Reamers Taper Shank HSS

Type 109M - Regrindable
Used to produce close tolerance surfaces and can be re-ground to give a greatly extended tool life. Ideal for production reaming of intermediate diameters. Manufactured to BS 328-4. Inch limits of Tolarance (to H7).

For all dimensional specifications please refer to our catalogue.

Expanding Machine Reamers - Metric

Sandvik Coromant CoroDrill 880 Indexable Drilling Inserts

Guide to Geometry/Feed:
-GM geometry is the basic choice for most materials. Medium feed.
-LM geometry is the best choice for long chipping materials, e.g. low carbon steel and stainless steels. Medium feed, insert with sharp positive edge.
-GR geometry is the high feed choice for steel and cast iron. Insert with strong reinforced edge, suitable for roughing.
-GT geometry is a problem solver for unstable conditions and interrupted cuts. Low to high feed. Good chip control in most materials.

For all technical and dimensional specifications please refer to our catalogue.

CoroDrill 880 Indexable Drilling Insert

Insert size: 880.. 03 03 W06H-P (Peripheral insert). Geometry: -LM. Grade 4014.

Sherwood Drills Taper Shank HSS

Suitable for single and multi-spindle drilling machines. The taper shank being the engineering industries recognised standard and most widely used method for holding and driving cutting tools. Manufactured to BS328;Part 1:1986, DIN345RN, DIN343RN.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT3) - Inch

Dormer HSCO Jobber Drills

A901 HSCo PFX Alcrona Top Jobber Drill
High productivity "one-hit" drilling to 6xD
Alcrona Top coating for extended tool life.
Excellent performance across a wide range of materials.
Size Range: 1.5 - 16.0mm, 1/16” - 5/8”

Sherwood Long Series Drills HSS

General-purpose high speed steel long series drills are designed for deep hole drilling of most materials. The drill has the same diameter on both the fluted section and the shank. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Inch